Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hello,
I'm trying to update the SoftDeivce used on our product from s140 v6.0.0 to 6.1.1, but am running into issues. Per the release notes it sounds like no updates / recompilation...
we use 52810 connect with iphone6, then read the RSSI value, it will disconnect with the iphone6.
reconnect the iphone6 and read the RSSI value, it disconnect again.
we...
After doing some reading, I realized that the light CTL server model does not contain the generic OnPowerUp set message. It is contained within the light CTL setup server...
After import a project in to SEGGER and included paths of header files
While compiling i got the error like below
sorry, unimplemented: non-trivial designated initializers...
Hi, I am using a system where I am using nrf52832 nordic chip. I generate a custom ble service using this ' https://github.com/bjornspockeli/custom_ble_service_example ' github...
Hello.
I would like to use the SPIS module on the nRF52840 DK. I configured it by following the examples given by Nordic.
When I use pins P0.14 (nCS), P0.15 (SCK), P0...
I am using now SDK 15.0 and the value of APP_ADV_DURATION is set to 18000 (180 sec)
But I saw that fromSDK15.2, it is recommended to change the value to 0 in order to get...
Hi,
We are running an application using REG1 only in DC/DC mode, REG0 is disabled. I believe we've found a small issue with our decoupling of all the power pins, but I'm...
Hello,
I am trying to connect my nRF9160 but am running into some trouble. Only LED 3 blinks for about 3 minutes and then just stays on without blinking; LED 4 never blinks...
Dears
I double the ble_nus_init as below ,I can get 2 service bouth have 2 characteritic.
as below:
err_code = nrf_ble_qwr_init (&m_qwr, &qwr_init); APP_ERROR_CHECK...
I am facing issue with programming of own developed nRF52810QFAA board. I used Pins 25 (clock) and 26 (data) along with Vcc and Gnd to flash device. I tried with two boards...
Hi, May I use slip library code for commercial? I have a project that uses an MCU communicates with an NRF52 BLE module. To upgrade program of BLE module, I flash the bootloader...
