I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Hi.
I am using SDK v2.6.0 (Toolchain v.2.6.0). When I open VS Code (v1.91.1) I keep getting this warning -->Bad CMake executable: “”. Check to make sure it is installed...
Hello,
Our product uses nrf52 and a quectel bg95 modem connected over the uart
We are evaluating the nrf connect sdk, we seek to have a working modem abstraction to send...
My device is an nRF52840 running a C Code application that is built on nRF5_SDK_17.1.0 I am implementing a FOTA solution where a hex file fw image and a .dat file will be...
I'm using the nordic ppk II to measure the power consumption of my device.
In order to validate the charge (current integral) displayed by the PPK2 i put two PPK2 daisy...
Hi, I need to program my custom boards, i am using nrf52840 DK which switches programming from the internal chip to the external one based on its presence.
Is it possible...
Hi,
I have a working application where at some point, I erase some part of the flash with following code :
On nRF52 aPageAddr is:
(not sure why other variables are...
Hi there,
I have multiple flash partitions defined in pm_static.yml.
I want one specific partition to contain a binary data file so that when I flash the image with J...
Hello,
I'm trying to do an HTTP multipart POST with chunked transfer encoding but am having trouble sending the headers to the socket. When trying to send, I receive a ...
SW version :2.4.0 HW revision: nRF52833 development board, PCA20054 Direction Finding Antenna Board 1_0_0 I use the routine director_finding_central and director_finding_periopheral...
Is there a solution from Nordic available where I can have a LTE-M (or NB-IoT) and at the same time still receive the 1PPS output from the GPS module? It seems to be that...
I am doing DFU using nRF52832 board. Is it possible to update partial firmware?
For example, Is it possible to change only blinking LED without changing other stuff from...
Hi, I'm having trouble finding out which update caused my application to crash. The build works fine with nRF Connect 2.43, but with the latest version (2.6), it doesn't work...
Hi,
I am writing a app.overwrite to remap my pins table. I can use
/delete-node/
The above is no problem. Bu my pio is overlay with gpio1 pin 5. The original dts...
We're using a noinit section of ram to store a "reboot reason" if/when we need to do a SW reset (i.e. in a watchdog handler).
This works as expected, we set the reboot reason...