Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I got a nrf51822 board and a st link v2 mini as shown below. I have been trying to connect the nrf51822 board so that i can upload code to the board by following this...
Hello folks,
I'm newbie on NRF, I have NRF51422 with Keil IDE and I want to create a mesh network on that kit which will continuously broadcast the data of sensors to the...
I am beginner to nrf51 i would like to increase my expertise on nrf51. Are there any recommended books/ tutorials/ weblinks whcih could help me to gain a better understanding...
Hi there,
We have designed our circuit board with the nRF52832 chip. One of the GPIOs is used to monitor a 12V power supply. We use a voltage divider on the 12V so the...
Hi.
I want to ask Nordic employees about the Queued Writes module. Tell me please, is this module required for all applications? If it is not required, then why in all examples...
Hello, i did the DFU quick start guide and everything work fine however when i try to send a ZIP file (124KB) with my own code the receiver show "Abort event. Reason: 0xD...
Hello ,
This nRF9E5 wake up function is driving me slowly nuts...
How to distinguish whether the wake up is coming from RTC or from GPIO.
I have tried to read the wakeup...
Hi
I'm working on a password pairing project. You must enter the correct password to connect properly. And This function can be normally implemented between mobile phone...
Hi . I am using Ublox NINA-B301 EVK for BLE developement. I am not using JLINK debugger . As this EVK is OPEN CPU I want to program the module with available examples in Linux...
Hi, We are in the process of migrating our SDK version from 13 to 15.2 and the error we were facing after porting of SDK is that , we were not able to track the BLE events...
Hi.I use SDK12.2.I want to blink the RGB LED.so I use pwm.this is my code but it only bule color light on.does anyone know why?
#include <stdio.h> #include <string.h>...
Hi Nordic:
I got a strange result, I compile a example of Mesh-sdk-2.2, such as proxy_client, then I copy proxy_client to another folder such as proxy_client_b and compile...
Hi,
I'm using PCA10040 to test the "ble_uart_c example" from the SDKV12 but it hangs after calling ble_stack_init() in the main.
I'm using IAR IDE to compile and debug...
Hi, Sir
I am developing a nRF52840 system with 1 ble peripheral link and 19 ble central links.Firstly, I implement ”19 ble central links”by modifying
nRF5_SDK_15.2.0_9412b96...