This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
I need to measure all width of continuous pulses without stopping the measurement. The pulse frequency is about 10kHz. But the frequency and the duty ratio changes dynamically...
Hello everyone,
It seems like a very basic issue but somehow I am unable to resolve it.
I have a characteristic of length 20 bytes. This characteristic is supposed to...
Hi everyone,
I am having problems in getting the twi peripheral to work properly with the accelerometer I am using ( NXP MM8653FC).
I am getting some wierd issues, firstly...
Hi,
I have noticed strange behavior when Android-Image-Transfer-Demo firmware is used (SDK13, softdevice 5.0.0-2.): Demo kit does not startup if powered from the coin battery...
Hello!
I am putting (with a wave generator) a square wave on pin 17 of the microcontroller, and I want that same wave to come out on pin 18.
How do I do that?
Do you have...
I'm using SDK v 12.2 project ble_central/ble_app_uart_c using GCC
After running the project for awhile a stack overflow in the ble_stack_thread() is detected which eventually...
Hi,
I'm modifying the light_switch client example, so that I can use GPIO as input instead of the button. I was able to build the modified example in SES and download it...
I'm attempting Mesh DFU on an Ubuntu 16.04 system. Here are the steps in the quick start guide along with corresponding notes on my setup:
nrfutil keys --gen-key private_key...
We are currently developing on the PCA10056 as we wait for our development boards. We would like to implement UART0 as a debug port, that we can output the log messages to...
Hi,
Can somebody explain how the Ax, Bx and Tx registers are used in the calculation of the temperature reported by the temperature sensor block in an nRF52832?
What we...
Hi,
I need to connect multiple SPI slaves in a daisy chain. It seems that using nrfx_spim_init once and nrfx_spim_xfer at each transfer is the simplest way to go using the...
hello, i want to synchronyze differents peripheral with a central thanks to the state of gpio i have this code but when i call gpiote() i hava nothing in return why ?
void...
I have done some reading on the forums and have seen that Martin Bohrs-Lind has ported the EMDv6.12 to SDKv14.2 and the nRF52832, here . I have keil v 5 compiling his work...
Hi
What would be the best way to interface a wireless charging circuit with a nRF52 device?
I've found a IC from Texas instruments that does the job, but is it safe to...
