Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
In the nRF52840 datasheet, peripherals don't appear to have shutdown or power-off controls but they do have enable/disable registers. I'm guessing that Device PM turns on...
Hi, I use periodic advertising to send live data based on readings from an accelerometer. I want to change the advertising packet after every advert to the new values.
My...
Hi there,
I am currently building nrf9160 custom board. But now I am planning to implement provisioning credentials like this URL https://docs.nrfcloud.com/Devices/Security...
Hi
The response to this ticket
says "You can implement active RFID. In active RFID you can for instance periodically wakeup the chip to turn ON the radio for a short...
Does Nordic provide a DTM application for the nrf5340 which communicates over the USB interface as a COM class instead of using a UART interface? It's been brought to our...
Hi Nordic team,
I debug on the board, and I want to check the connection at the first time without connection before. so I want to clear data on the flash first, then...
Dear Nordic Experts,
Is there any way to detect the the WDT has reset the system. I mean some WDT register from which you could read this information, and that would be...
Hi,
I use nrf5340 with nrf connect SDK 1.9.1
I found some issue when: 1. My peripheral device that running connected and paired to some Central device.
2. The central...
Hi guys. I was observing the PCA10121 PCB layout using this link.
From Murata SWF connector datasheet, it says
https://www.murata.com/-/media/webrenewal/support/library...
Hi,
I am using NCS 2.1.2 with the [email protected] (but I have tested with 2.2.0-rc1 and it doesn't change anything). I have attached a simple example which should just...
Hi team,
I want know how many UART modules on nRF52840 microcontroller? I am confused with one UART and two UARTEs.
Which one is connected to "USB for interface MCU" connector...
Hi,
I have successfully followed the guide for setting up the AWS asset tracker application ( https://nordicsemiconductor.github.io/asset-tracker-cloud-docs/v2.1.x/docs...
Hi all,
I did add a reset switch on my custom board. I read some topics how to active it, but I´m not sure if I did it right.
I did add it in the preprocessor define:...
Hi Nordic,
Soft device is s140
SDK version is: nRF5_SDK_17.1.0_ddde560
Bootloader - Secure bootloader.
We are trying buttonless DFU process using secure bootloader...
Hello,
We are trying to use the nrf91 GNSS with the `nrf_modem_gnss` library. I'm looking for clarification on these fields that are listed in `struct nrf_modem_gnss_agps_data_location...
