When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi all：
We update SDK from 11.0.0 Version to 17.0.2, the hardware is same, but from 17.0.2 package, we run DTM in single channel mode ,data lost is 40%. DTM from 11.0.0...
I have an issue with creating a Bluetooth mesh gateway. It would be better to use nRF Connect SDK for me, but nRF5 for Mesh is also fine. As I've found among answers, not...
Hello guys,
I try to implement a pdm sensor on the nrf 52 dk which sends the audio data to a central device.
My setup is two nrf 52 dk one acting with the modified ble...
Hi,
I am developing application in nRF_connect_SDK v 1.4.2.
I have a problem in Debug the code 1. When i debug the code the breakpoints is not appearing
2. When i...
Hi Nordic,
how do i interpret properly return errors? I l know that it depends on the base address but sometimes it does not correlate at all.
For example, currently...
Dear friends,
We want to update the bootloader in our project. I have read the tutorial about the DFU process from here " Dual-bank and single-bank updates ". I have some...
Hello I would like to change from nrf52810 to nrf52805. I want to take the same code, but I want to change only the gpio because the gpio is different. I was going to set...
When I try to connect to my Pure-FTPd server I always get an error when trying to login, but If I use a public server like... https://dlptest.com/ftp-test/ it's fine. This...
Hey all!
We want to improve the accuracy of the localization of our asset tracking solution, in particular indoors. For that we want to scan Wifi base station advertisments...
Hello,
I am trying to get an MQTT TLS connection to AWS up and running on my thingie91 (nrf9160). I am using SDK 1.5.0 and the sample "aws_iot".
Even though there is a...
Hello,
what is the CPU speed of nRF52832?
I'd like to test if the NRF52832 is running at 32MHz or 64MHz.
I used it to run a compression algorithm, which took 8ms to...
I have seen this question asked a few times--but every thread seems to have no concrete answer.
I have uninstalled and reinstalled all JLINK drivers.
But still get the...
I am using the nRF9160 for IOT with the console connected on UART 0 there is a string of +CSCON: 1 and +CSCON: 0 messages displayed.
Build Zephyr 1.5.1
Modem firmware...
