I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am going to programme the nrf52840_pca10056 DK with Arduino IDE. I was folow this tutoriol https://how2electronics.com/nordic-nrf52840-advanced-bluetooth-5-arduino-ide/...
Hi,
I am trying to set up a bootloader using the example code given in SDK 15.3.0. I am working with the nrf52840 dk and have been using the same device with the same project...
We are working on requirements for a design based on the nRF52832. Does Nordic have characterization data to share of the temperature dependency of clock drift of LFCLK?
Hello all,
I've got a Thingy 9.1. I've successfully built and flashed the serial_lte_modem example (with no changes) onto the device but when I open the serial port in LTE...
Hi,
I dowloaded mesh 5.0 sdk and open light_switch example project with SES which installed in a 64bit windows 10.
I set the SDK ROOT as following the step of online guide...
Hello,
I have just started in the world of Nordic products and quite recently in the embedded world. I'm trying to learn and understand the use of zephyr in basic projects...
Hi,
after migrating functional project to latest ncs version v1.5.0 I managed to build and flash it to nrf52840 board without problems. However if I enable MCUboot option...
Hi guys,
I want to add the function of multiple slaves to the nrf_desktop routine to support two hosts to connect to the keyboard .This routine is in the ncs1.4.1\v1.4.1...
Hi,
My application is to scan BLE advertising packet.
My application works when the scan_phys is set to BLE_GAP_PHY_1MBPS.
params.active = true; params.interval = NRF_BLE_SCAN_SCAN_INTERVAL;...
I'm specifically interested in the predefined SPIMn - SCK, MOSI, MISO, SO pins for this device, so that I can marry this information into my CPU Schematic Page. Whilst the...
Hello,
In our application, we have an external watchdog IC. We need to test the timing of that chip during our board power-on self-test.
We currently achieve this by setting...
Hello!
Recently we have noticed that some of our devices has been reporting strange fulgurations on their reported battery level. This is a graph over 24 hours:
When...
Hi I am the evaluation board of nRF52832 (TAIYO YUDEN Evaluation Board) EBSHSNZWZ) is used. I want to use P0.09 and P0.10 of nRF52832 as PIN of GPIO(TWI). It was set according...
Hi,
I'm developing a serialization system with nRF52832 and an application chip. My product is a power-sensitive.
The code of ble_connectivity in nRF5 SDK 17 calls nrf_drv_clock_init...
