I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
As title.
In nRF54L15 DK, I set "SB_CONFIG_BOOTLOADER_MCUBOOT=y" in file "sysbuild.conf".
It makes main function GPIO toggle stop.
Do have any solution to prevent...
Hi,
I am developing a custom PCB based on the nRF52840 and am currently trying to flash/debug it using an nRF52840-DK (PCA10056) as an external debugger.
connected devices...
Hello all !
Summary
While in power save the nRF7002 RPU powers down its receiver without sending a PM=1 (Null) frame first, so from the AP point of view the station...
Dear Nordic team,
we are evaluating the nRF9151 for a data acquisition application/device. Our first goal was to get the official HTTPS client sample to run on the nRF9151DK...
Hello,
I work on a zephyr project with updatable MCUBoot and two updatable images. This configuration ends up with an unbootable image. The reason is that the CONFIG_MCUBOOT_MCUBOOT_IMAGE_NUMBER...
Environment
SoC: nRF54LM20 (DK; silicon reports nRF54LM20B ENGB — also reproduces built for the LM20A target)
nRF Connect SDK: v3.3.0-rc2, west v1.5.0
Bluetooth: SoftDevice...
We are currently experiencing an issue with the nRF7002 that appears to be present when coexistence is enabled: The nRF7002 becomes unresponsive, seemingly at random, multiple...
Title: nRF52840 / OpenThread: how to inject custom IEEE 802.15.4 RX frames into the native receive path?
Hi,
I am working on a test setup around nRF52840, OpenThread,...
We want to measure latency and PER between two OpenThread Nodes exposed to WiFi interference. Multiple Raspberry PIs, which are configured as AP and/or client, simulate flooded...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Board: nRF54LM20A DK NCS version: v3.2.1 Sample base: nrf/ samples/zephyr/subsys/usb/cdc_acm
Background
I am evaluating power consumption on the nRF54LM20A DK before...
Hello support!
I am using the nRF9151 and the nPM1300 on a custom board.
Is is possible to measure the current drawn by the board via the VBUSIN? The reason is too have...
Hi
I have custom nrf5340 based product, with an NFC interface for card emulation. I have managed to get this to work in raw APDU mode in NCS 2.9.0 (with selected cherry...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
