Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi nordic:
As shown in the figure below, I see that the BLE protocol standard mentions the ScanReq backoff mechanism. Does NORDIC implement it?
jermi.jin
thanks!!...
Hi,
The central_uart sample hardfaults when bt_enable(NULL) is entered. I can use the debugger and step over the first couple lines but stepping over bt_enable causes a...
Hi
I have integrated the example code for mesh dfu provided in the nrf mesh sdk5 in my main application . I have followed all the steps mentioned in this dfu guide. The...
Hi,
We have a working LwM2M device based on nRF9160 and NRF Connect SDK 1.1. When we run with a short register-update period (30 seconds) on a NB-IoT network it works. When...
Good Morning,
I would like disable passkey in the example "peripherals_hids_keyboard". I am able to connect with differents hosts (2 smarts and i computer) but I'm having...
On SoftDevice S140(V7.2.0)
ble_gap_adv_report_type_t status has four types.
BLE_GAP_ADV_DATA_STATUS_COMPLETE BLE_GAP_ADV_DATA_STATUS_INCOMPLETE_MORE_DATA BLE_GAP_ADV_DATA_STATUS_INCOMPLETE_TRUNCATED...
I am using nRF Connect SDK with VS Code on Ubuntu 20.04. I have installed SDK using the nRF Connect for Desktop and Toolchain Manager.
When I start VS Code I get the following...
Hi, I am trying to see the connected devices by executing the "lsusb" command, these are the steps I followed:
1.- Connect USB / swith NRF power Source to USB:
2.- Click...
Our development environment extends the NCS for our 9160 and 52840 hardware. To create a command line build environment in v.1.x.x, I was able to leverage the env.cmd file...
I have migrated an application based on the peripheral uart sample, running on a Fanstel BT40 board, from nRF Connect SDK v1.6.1 to v2.0.0. The application receives one line...
Hi,
I am trying to send data to a http server, and are trying to error handle. I am looking trough the documentation on the send() funciton in the socket.h library, but...
Hi,
I have an issue with interrupts on TIMER1 on nrf5340 NETCPU. My setup involves 2 timers that are linked via DPPI, TIMER2 counting microseconds and TIMER1 counting milliseconds...
Hi!
I am currently using the ADC to take two thermistor values from 2 AIN pins. Currently we are using the 10 bit ADC but I am looking to achieve 14 bits with oversampling...
Hi Devzone
currently we found the time cost for memset has increased after the project the use NEWLIB_LIBC
inside the project , we use funcation k_cycle_get_32 to calulate...
