Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I send and receive 1:1 using an ESB with nrf52840. I do not want to "use nrf_esb_start_tx()", but instead use PPI to trigger a specific event to be sent.
I want the PPI...
Hello
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0. Recently I have encountered the below issue:
err_code = app_timer_start(m_loadcell_timer_id...
I use 52833dK,Wpanctl whether there is a command to send custom data in the thread network.Similar to UDP in cli.
I found that there are relevant codes of HDLC software...
Hoping someone can help.
I am using an nRF52840 MDK USB dongle running nrf firmware in wireshark / nrf sniffer. I am attempting to sniff the bluetooth messages from my pool...
Hello,
I'm trying to get SPIM working with a nRF52840 DK, PCA10056.
I downloaded the nRF5 SDK 17.1.0 and I am able to build example projects, and I verified that I...
Hello,
Do you know where I could find a sample to read NFC Tag with Thingy91 ? The best could be to have a sample sendind on MQTT NFC tags reads.
I read different posts...
Hello, I need help to clarify an idea. What I want to do is get data from a Main board (Custom uC with sensors) via UART and connect it to the UART set pins (29 and 31) of...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056...
Hello,
I have a custom board using an nRF9160 chip. It connects to the Nordic Cloud. Modem firmware 1.3.1. SDK 1.6.1.
I have seen an issue 3 times now over ~6 months...
Hello, guys.
I have nRF51822 SoC running Zephyr OS. Among the other things, the nRF should communicate (over I2C) with the touch controller that will fire an interrupt every...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am a beginner at Nordic. I want to understand how I can access a pin named " P1.04 ...
Hi,
I faced the exact problem nda , here . I take step just like nda did before. I unchecked "Enable debug options" as Marte Myrvold told, but still the same problem.
...
I am working with nRF connect SDK with nRF52840 dongle. I am compiling code using nRF coonect for VS code with nrf52840dongle_nrf52840 board.
For Programming nRF52840 dongle...
Hi
I have similar question to the post https://devzone.nordicsemi.com/f/nordic-q-a/7013/nrf51822-internal-ldo-output-pin .
I need a stable voltage to elevate the reference...
Hello everyone,
I use the multirole software as base for my application and I programmed everything with a evaluation board. I design my own PCB and decided to not use the...
