I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I have an encased nRF52840 dongle that is visible to nRF Connect. However, when I try and select the displayed device I get the following:
I cannot press the reset button...
Hi,
1. What modem versions does this board support?
For example mfw_nrf9160_1.3.0？
2. This board programmer this example:lwm2m_client
Using AT + CFUN? No return...
Dear Nordic team,
in our multiprotocol (BLE, ZB) application ( nRF5 SDK v4.1.0 )we are facing following severe issue relating to the ZBOSS stack: When a router leaves its...
Hello sir/Ma'am
I am working on a project in which i am using some BLE peripheral devices, an Central device and an Android app. I want to get data on android app from central...
I'm trying to program nrf9160 but getting an error due to readback protection.
I have tried the following commands:
nrfjprog --recover
nrfjprog --recover -f NRF91
...
I set an NOPULL type input GPIO, and I found that if I put in a voltage of about 1V,
the nrf52832 will produce a current of about 30uA,
I want to know why it can be happen...
HI
I have using nrf5340 DK for the past 7 months. Sometimes, The DK gets powered up only after 2-3 minutes after giving the power supply from the PC. Even after powerup...
I'm working on a project based on nRF52840 and nRF5 SDK16. I'm using BLE with softdevice S140 7.0.1 and USB CDC ACM for communication with a USB host. Ultimately the problem...
Hi,
I'm trying to run ble_app_blinky_pca10040_s132 on Fanstel BT832 custom board with no success. After writing/verifying the app using the SES it jumps to 'unknow function...
Hello,
I have a question:
i want to send a JSON payload using the PUT-method from CoAP. For this I am creating my JSON Payload with the following function:
The main...
I am in the conceptual stages of development for a BLE test system.
The test system requires:
Fast transceiver and connection with BLE devices, preferably capable...
I know Nordic is releasing the nrf9160 on the 12/12/2018, and from what little documentation I can find it doesn't seem to have BT or NFC hardware integrated. Are there any...
Hello, I have installed nRF Connect and the Programmer following https://infocenter.nordicsemi.com/pdf/nRF9160_DK_Getting_Started_Guide.pdf At step 3.2.2 i see "No devices...
Where can I find a drawing of the footprint for the nRF52840 WLSCP? Normally it would be near the end of the datasheet, after the mechanical drawing of the package. The datasheet...
I have an application running a serial communication through a RS485 interface. I have two sensors attached through I2C/TWi.
I have a app_timer that quwry the sensors once...
