Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I develop a test fixture based on nrf51 code that I use for final product.
NRF51 is just a part of a complex test fixture, then I have just "one" test fixture model.
I...
Does m_xfer_done need to be set to false before calling nrf_drv_twi_rx? If so, does while (m_xfer_done == false); loop need to be called on every read?
I'm developing a Bluetooth mesh device on a Window 10 machine using Segger Embedded Studio v4.52c on a nRF52832 chip using SDK16.0.0, Mesh SDK 4.1.0 and FreeRTOS.
in the...
Dear all.
I just got nRF52 DK and testing blinky based on KEIL and it works well.
I tried one test, IF BOOT/Reset, and nRF52 PDK is not working after below sequence. ...
Would it be possible at all to add a preset text string to the current advertising data, in an advertising-only module configuration, by changing the logical input of one...
Hi,
I've upgraded my SDK from 15.2 to 17.
After upgrading - I can't connect my device via NFC - it keeps disconnect with NRF_ERROR_RESOURCES .
I've tried to increase...
Hi
My goal is to create a USB HCI firmware that works on any custom board that exposes the USB port of a nRF52840. Based on the requirement for USB HCI it was clear to use...
Hi, I am working on an OTBR, nrf52840 connects to the router through SPI, I want to know how to upgrade 52840 through the router. The router use OpenWRT. p lease give me some...
Hi,
Our devices are getting randomly bricked by updating firmware through mcumgr in Zephyr. It happens on both the nRF91 and nRF52 chips when we run the latest nRF Connect...
It's strange, My nrf52840 can't boot up after power on,unless it was connected to JLINKRTTVIEW, If I disconnected the JLINKRTTVIEW, the device will stop running, Connect again...
Can anyone tell or give a pointer to info about RFCOMM vs. NUS (or any other vendor specific UART emulation service)?
Why are there vendor specific UART emulation services...
Referring to the Nordic message sequence chart in the following link:
https://infocenter.nordicsemi.com/index.jsp
(Software Development Kit -> Previous Versions of nRF5...
Hello!
I use SDK v17 and using the library and example code for the lsm9ds1 sensor.
github.com/.../nRF52-DK-and-LSM9DS1
'lsm9ds1_reg.c', 'lsm9ds1_reg.c' these two files...
Hello!
I am using ble adc scan mode example and successfully tested it with nrfconnect by sending my data from AIN3 . Now i want to send data of ble to raspberry pi bluetooth...
