Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
Hi:
I am using a shake sensor as an analog input wake-up system. The system is not system off. The analog input signal only generates an event to wake up turn on...
I am using the UART central, integrated with peer manager and UART peripheral application from the SDK 15.3 on our custom hardware. I have 2 centrals running exactly same...
Hello everyone.
I want to familiarize with The Power Profiler Kit. I've installed proper software and been trying to connect to the device but every time I receive the same...
Hello,
I am trying to load the ble_app_hrs example from sdk15 on to my external BMD-350 module, but I cannot seem to discover the module using nRFConnect. I am not using...
SDK:
nRF5_SDK_15.2.0_9412b96
Softdevice:
132_nrf52_6.1.0_softdevice.hex
Hi Sir,
I want add NUS function to ble_app_hrs_rscs_relay sample code and I add...
Hi,
I use a central with 4 peripherals connected with BLE protocol.
On the central, I use the radio notification interrupt. I would like to know which peripheral correspond...
Hi,
I have a problem in my application, i want to add scanning feature, but
When i call sd_ble_gap_scan_start () with these parameters it returns error (0x06) (with...
I am a begineer in Nordic trying to read voltage and current readings from ADC pin. I need to read both values in parallel, with known interval. So I need to use interrupts...
I am trying to use the LTE Sensor Gateway app to send Running Speed and Cadence Service Sample Application data loaded on a nRF52832. I have managed to get this two device...
Hi,
I have a problem with timer and nrfx. I use the migration guide:
So I r emove the old configuration entries related to the nrf_drv_* drivers from my sdk_config.h...
Hello,
I am currently using nRF52832 with SDK v11.0.0 and S132 v2.0.0. I am also using the soft device as my application requires. I have been trying to put the CPU into...
Hello, When i try to use nrf9160 with the BME280 sensor over I2C i get this error
***** USAGE FAULT ***** Illegal use of the EPSR ***** Hardware exception ***** Current...
Hello,
I am using BLE+MCU MBN52832 module and i am facing one issue while programming my application.
I am uploading the hex file using nrfGo Studio and when i try...
I have a custom nRF52840 board that I am implementing the Open Bootloader (from SDK 15.3). Push Button/Power control is handled by the STM6601 device. It keeps the power ON...
When I open a new project in SES and paste the code of blinky led example from " \nRF5_SDK_15.3.0_59ac345\examples\peripheral\blinky\pca10040\s132\ses ", and start compiling...
