I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hello,
I would like to modify the current default SRAM partition from 64k (secure), 64k (bsd), 128k (non-secure). I would like to change it as follows; 8 k (secure), 8k...
See: https://devzone.nordicsemi.com/f/nordic-q-a/46833/nrf-connect-can-t-see-nrf52-dk/185284#185284
I have been developing a peripheral with nRF52832 and SDK 15.3.0.
I...
I'm stuck over fds_init() which hangs on mbed-os using SDK 14.2
I am calling fds_init within bleInitComplete callback as follows:
BLE & ble = BLE::Instance ();
ble...
Hello,
The pwm example shows changing the duty cycle inside the main while loop with delay wait.
I would like to get rid of this delay wait by putting the app_pwm_channel_duty_set...
Hi, may I know whether there is a way for nRF52832 chip to directly have access to the variable gain amplifier (VGA) inside the chip? Namely, our input signals goes directly...
Hi,
I am using the sdk 14, S132, ble_app_uart example.
My nordic chip receives data from the MCU over UART and passes out to mobile application over BLE.
using the nrf...
hi i am trying to integrate nrf_butoonless_dfu service in ble_app_uart code in nRF sdk 15.3.0,
i have added the all the required source files and include files and macro...
I am attempting to implement an application using the s140 6.1.0 softdevice on an nRF52840 which "concurrently" advertises as a connectable device while at the same time transmits...
I try to solder a EBYTE NRF52840 module by my PCB and connect with SEGGER programmer. I try to connect to 4 wire VDD, GND, SWDIO, SWCLK, like the one that I have with NRF52832...
I'm migrating a project from SDK 14.2.0 to SDK 15.3.0. I use gcc. I just got it to link and flash and I'm seeing RTT logging OK, to a point. I also have the flashlog in use...
in my application use nrf52 connect with max6675 thermo couple for read temperature
max6675 is configurable in spi mode.
in main.c
in 'nrf_drv_spi_init' not...
Hello,
I use the LAIRD module BL652 with an nRF52832.
My project used the RTC as date/hour counter. I used this RTC to increment a counter each 125 ms of RTC interrupt...
Hi,
I am using s132 6.1.1 with SDK 15.2, developing with keil , my code works completely fine on Development Kit but it doesn't boot up on our custom board which doesn't...
Hello all,
I updated modem firmware mfw_nrf9160_0.7.0-15.alpha.zip. I have iBASIS SIM card in modem and started with at_client example and country also has nb-iot support...
