When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello ,
I have met a problem about the communication between nrf52832 and nrf24le over Gazell. nrf52832 is the device and nrf24le is the host. The problem is that nrf24le...
https://devzone.nordicsemi.com/b/blog/posts/measuring-lithium-battery-voltage-with-nrf52
Following the calculations as so, I have worked out the necessary capacitor values...
Hi,
I am using the command line tool nrfjprog to read the device MAC address using the following command:
nrfjprog --memrd 0x100000A4 --w 8 --n 6
I am connected using...
hello,
I want to use nRFgo studio download hex for NRF52810, but I have a problem as follows:
I do not know how to solve the problem, thank you very much!
best regards...
Hi,
I'm using an application based on the light switch provisioner example (BLE mesh 2.2.0).
I'm wondering if the following is possible:
- Request all provisioned nodes...
Sir/Madam,
I am developing application software using nRF51822 in keil microvision 5 IDE. I want to know how to download the hex file without using KEIL IDE. I found the...
I'm looking for an equivalent simple DFU bootloader over UART similar to the HCI example which was provided in the nRF5 v11.0.0 SDK.
Currently, I'm developing with the Sparkfun...
hi,i have a problem! How to Optimize code space in nRF52810,s112,SDK15.2.0,example ble_app_hids_keyboard.
my method is that disable all the code which run in main function...
Hi all,
Now, I have a troube. In Mesh 3.0, I want to advertising data. This is my function :
#define ADVERTISER_BUFFER_SIZE (128)
And whenever the data changes, I...
I bought a nRF52840 Dongle, to evaluate the use of nRF52840 for ZigBee purposes.
I have been able to flash such firmwares as \examples\peripheral\blinky\hex\blinky_pca10056_mbr...
I have a custom board where both nRF52840 and nRF52832 SOC in it.
i have flashed example Ble_Uart code from sdk15 in nRF52840 but im facing a serious issue.
i can able...
Tôi đang sử dụng bảng nrf24l01 để định vị trong nhà, nhưng tôi gặp vấn đề với định vị TOA và bảng arduino không đo thời gian nhỏ hơn micros, tôi không biết bạn có lời khuyên...
Dear Nordic,
I am trying to setup a custom BLE client service to interact with the Komoot app (Turn by turn navigation).
I can connect to the phone, and receive notifications...
Hello Team,
I am trying to run the example DFU overt TFTP, however I found the description a bit ambiguous. Seeking help to remove my ambiguity.
I am trying to follow...
