When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I want to connect my mouse to win7 or XP PC(but I can only buy CSR BLE dongle CSR8510A10),
It connect OK in win8 with the same dongle but report error as the title describe...
Hi,
I have a problem is that I use the 51822 as a reader to read the 24l01's radio data.Now,I use the UART to read the instruction from the PC. If the instruction is "ON...
Hi,
I use the nrf51822 to read the data from the tag which designed by the 24l01p radio module.In the whole progress, first of all, the reading module read the instructions...
I have interfaced nRF 8001 with Arduino through MISo,MOSI,SCK etc pins and it is connected successfully. When i connected my arduino with pc, i thought nRF 8001 will start...
I'm trying to make a simple BLE app based on LED button demo (BLE_LBS.C) that probably don't use much resources. I added FIFO UART communication routines and when I tried...
I have an NRF 8001 BLE chip, can you provide the break out board schematic to make this chip discoverable to my iPhone 5 as soon as i power that break out board. And how to...
Can anyone tell me how to connect NRF 8001 with Arduino mega 2560. I have developed an iPhone application and just want to connect with NRF 8001.Please tell me how to connect...
OK, probably a dumb question:
The nRF51822 reference manual indicates that the RTC is driven by an external 32 KHz input. Can anyone confirm whether it will or will not?...
Hi
can you please help me convert these Keil pre processor calls to something that gcc compiler can . If possible i would like more information about these calls and the...
I'm using Nordic NRF51822 and the Segger JLink with the s110 Bluetooth stack active (correction: flashed on the chip, see below). When my code hard faults (say due to a dereferencing...
hi, I currently stuck in the follow section:
static void gpiote_event_handler(uint32_t pins_low_to_high, uint32_t pins_high_to_low)
{
if (pins_high_to_low & (1 << BUTTON_0...
Anyone to tell me where can i get the CDB file for nRF24LE01? I've downloaded the SDK and the nRF go Studio, but i still cannot find the CDB file.. Please help me to find...
Hello,
I'm trying to start softdevice on a custom board with nRF51822 chip and S110 device. The code hangs in SOFTDEVICE_HANDLER_INIT. It seems that EVENTS_LFCLKSTARTED...
Hello,
firstly I would like to say that I tried searching the forum for a post that has similar problems to my own. But I haven't (please tell me if i'm wrong) seen any...
