Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi there,
We are quite new to Zephyr. We are currently porting our existing app onto Zephyr as a test. We are currently using NCS 2.5.1
So for our existing application...
I needed to add my own partition to the primary flash, and was able to do so successfully by adding a section to the device tree partitions.
However, when adding MCUBoot...
Hi,
I'm trying to setup my NFR52840 DK to act as a NFC tag so that I can read some simple data on my phone via NFC transfer.
I have tried a few NFC sample applications...
Hi,
I am using a modified HTTPS Client demo code [Let's say Version A] and sometimes when trying to debug with Segger Embedded Studio for ARM (Nordic Edition v 5.34a/Jlink...
Hello,
From time to time I am getting the error " Unable to find bootable image" when I start a debug session in SES-NE v5.60.
FIH_CALL(boot_go, fih_rc, &rsp); if (fih_not_eq...
I am trying to read the GPIO state on an nRF52840 right after it wakes up from deep sleep (System OFF mode). I have configured 4 pins as wake-up sources from deep sleep System...
I have been working on finding the cause to an unexpectedly high power power consumption in several newly produced units of our product based on nRF5340. I believe I have...
I'm trying to build a custom secure partition, but get the following error when building:
However when navigating in files to the directory the file "tfm_custompartitiontest...
Hi All,
My team recently reserved a custom service UUID with the Bluetooth SIG, and we'd like to replace the custom 128-bit UUID we had been using in our products. Can I...
HI
We are mass producing NUS-based products.
During mass production testing, pairing is performed and functionality is tested by pressing buttons, etc.
However, pairing...
I'm using
AT_MONITOR ( catch_all , ANY , on_modem_at_notification );
and I'm just printing the notification on reception:
static void on_modem_at_notification...
Hello,
I would like to add to my project new i2c slave (for example - dac5571 from TI). In the DTS overlay - under the i2c0 node I need to specify compatible , and I don...
I have configured the nrf52840 DK one board as Peripheral and other as central.
Added multiple services and characteristics. I am sending some data at every 20ms using notify...
Dear all:
Customer products in normal mode, BLE works normally, all functions are OK. An error occurred in DTM mode during authentication. Procedure The failure status is...
Using the SDK 15.0.0 SPI example (master) to send a single byte.
Sending 0x00:
Sending 0x01:
Sending 0x02:
Sending 0x04:
etc ...
Sending 0x7F:
In all the...
