Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi,
I am trying to communicate with nRF9160, which is flashed with Nordic SLM application.
I am not able to set the HWFC with UART0/UART2 using menuconfig in Segger...
"Failed to upgrade target. Error is: Lost connection in the middle of the transfer"
I am doing a mesh serial DFU with DFU quick start guide .
I have gotten all the way...
Hello everyone,
I want to be able to set a timer in my project. With this timer i want to be able to make my current comsumption evaluation easier.
I am using the nrf9160...
Cannot update modem (nrf9160) with "nrf connect 3.8.0"
Modem DFU failed with error: no matching trait found
no matching trait found
Installing older versions eg...
The datasheet tells me that the default source of the low frequency clock (LFCLK) is the 32.768 kHz RC oscillator (LFRC). so I took the crystal oscillator off my PCB, but...
After updating NRF Connect v3.9.0 to eliminate the recently documented JSON + connectivity errors with nrf Programmer and Power Profiler, my bash scripts utilizing nrfprog...
Hi，
1. Please provide me with an example of BMA280
2. The SDK: replication v1.7.1
3.IC:nRF9160
4. I tried to change the BME280 driver to BMA280 driver, but the following...
I am working on project in which i want to read data from sd card and send it to mobile through BLE , I am using ble_nus_send to send data but when i decrease the delay then...
Hello,
Using sd_ble_gap_adv_set_configure() with ble_gap_adv_params_t I observe that the actual time when the BLE_GAP_EVT_ADV_SET_TERMINATED event is raised is earlier to...
Hi All,
Likely because I am still quite new to this, but I have started with MQTT simple example and whenever I do use GuiConfig to make mods, it saves them to
proj/build...
The disccussion here
https://devzone.nordicsemi.com/f/nordic-q-a/24592/my-nrf52-nrf51-dk-kit-doesn-t-work
has been closed.
I followed step 4 and it took a few tries...
Hi,
I use a Segger JLink EDU (the big version, not the mini) to flash some custom boards. This used to work fine until I upgraded nRF Connect and got Programmer v2.0.
...
Dear sir/madame,
By an accident I selected Power Profiler Kit II when I wanted to download an application to “PCA10056 DK” . After that ‘download’ Power Profiler Kit II...
Hello,
I'm using NRF52832 as a controller for cellular modem and used the AWS IOT supplied with the NRF Connect SDK.
I want to use the AWS FOTA and I'm a bit lost, I added...
