Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
Dear Sir,
I am working on NRF52 and I have DK of PCA10040 / V1.2.1 / 2017.36 / 682236729. I have done program advertising with scanning both in one program. then I used...
Hi, I have problem. My NRF52832 Dev board is not recognizable by anything. L05 diode is blinking every 0.5 sec. I used Segger - not recognized, Keid again J Flash same story...
Hi,
I'm developing a BLE mesh project using Mesh SDK v4.2.0. I want to change the Tx power of the product in real-time, e.g. from 0dBm to 4dBm, 4dBm to 8dBm.
I've read...
I have an application that is running for a while and then it crashes.
Execution goes to softdevice_fault_handler(), calling it with parameters: id=1; pc=0xf764; info=NULL...
hi all
A silly question here , I am prepare to meet some security compliance , one of them is about delete files permanently.
I wonder how to get this done on nRF51822...
Hi,
I would like to wake the nRF52840 SoC from sleep via a GPIO High Pulse input.
What is the minimum allowable pulse period do I need for it to successfully wake up...
Hello,
I have the following application code (based on the template project from the SDK):
The receive callback is working and I get all the characters from my terminal...
From the datasheet I understand that any pins in port0 can be used as SPI. But I tried using the pins defined in nrf-sdk here and but there is no response. After searching...
Hi!
I am kind of DIY person and have a lots of time in COVID, I am a beginner to Nordic family, few months ago I implemented MPU9250 with NRF52832, I was able achieve...
Hi !
I am working with nRF52 DK to drive the nRF52832 and a sensor of Maxim Integrated.
I am using an older version of the SDK (14.2.0) because i need to modify an old...
Hello,
I was looking at power profiler (just playing with it) and I run it without proper setup on nrf52840DK, after that It seems that dk does not execute any application...
My application is again having troubles with opening an AF_LTE socket. It hangs indefinitely on the call to socket(AF_LTE,...). This code has been running successfully at...
i use nrf51822 and uart project
i need disable only RX when tranmitsion and reuseable when tranmistion complete. i tried
//NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled...
