Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi. I tested extended advertising of Bluetooth 5 with examples, ble_app_rscs_c and ble_app_rscs , in SDK 15.2. It works well.
And I added 216 bytes manufacturer's data to...
Hi,
I am doing a job with nRF52832 with keil in initial period. I have two peripherals and connect to nRF52832 via uart, and it runs well. Recently, I migrate the job to...
Hello ,
I have met a problem about the communication between nrf52832 and nrf24le over Gazell. nrf52832 is the device and nrf24le is the host. The problem is that nrf24le...
https://devzone.nordicsemi.com/b/blog/posts/measuring-lithium-battery-voltage-with-nrf52
Following the calculations as so, I have worked out the necessary capacitor values...
Hi,
I am using the command line tool nrfjprog to read the device MAC address using the following command:
nrfjprog --memrd 0x100000A4 --w 8 --n 6
I am connected using...
hello,
I want to use nRFgo studio download hex for NRF52810, but I have a problem as follows:
I do not know how to solve the problem, thank you very much!
best regards...
Hi,
I'm using an application based on the light switch provisioner example (BLE mesh 2.2.0).
I'm wondering if the following is possible:
- Request all provisioned nodes...
Sir/Madam,
I am developing application software using nRF51822 in keil microvision 5 IDE. I want to know how to download the hex file without using KEIL IDE. I found the...
I'm looking for an equivalent simple DFU bootloader over UART similar to the HCI example which was provided in the nRF5 v11.0.0 SDK.
Currently, I'm developing with the Sparkfun...
hi,i have a problem! How to Optimize code space in nRF52810,s112,SDK15.2.0,example ble_app_hids_keyboard.
my method is that disable all the code which run in main function...
Hi all,
Now, I have a troube. In Mesh 3.0, I want to advertising data. This is my function :
#define ADVERTISER_BUFFER_SIZE (128)
And whenever the data changes, I...
I bought a nRF52840 Dongle, to evaluate the use of nRF52840 for ZigBee purposes.
I have been able to flash such firmwares as \examples\peripheral\blinky\hex\blinky_pca10056_mbr...
I have a custom board where both nRF52840 and nRF52832 SOC in it.
i have flashed example Ble_Uart code from sdk15 in nRF52840 but im facing a serious issue.
i can able...
