Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I want to advertise the beacon with its name visible using the ble_app_beacon example but not able to understand how to proceed.
With this, I am not getting how can...
I want to make the led ON always and making the source code from scratch in keil mu vision 5. I am not able to understand which library is to used and how to proceed.
I'm using nRF51822 to communicate with nRF24L01+ without SoftDevice, and it is working fine.
But when I add app_timer.c to the project and compile, it will show the following...
Hi,
I am able to program my custom board using nrf52dk (only 32 Mhz osc populated on custom board), and I can also see the output of SEGGER_RTT_WriteString() though JLinkRTTClient...
We've been suffering Unreliable Auto Connection for quite a while... "autoConnect" sometimes just doesn't work to get the device back to connection. Below is the failure message...
Hello,
I started with example apps and have got one working with the supplied makefiles, gcc, and Eclipse. I'm able to debug my code without trouble, and have succeeded...
When I try to write a UUID into the UICR registers using the method described at - Software Development Kit > nRF5 SDK > nRF5 SDK v12.2.0 > Examples > Hardware peripheral...
Hi Team,
I´am working with the nRF51422 and would like to change the parity from even to odd.
Is there any possibility to change that setting or just to invert the even...
Hello,
Is there any possibility to configure the UART parity to odd on chip?
I am using the nRF51822 chip. I could activate the parity but inside the documentation they...
Hello
I am building bootloader. I do not use Softdevice and used example from this topic . Bootloader must read FW from uSD card, update flash and jump to application....
I am using nrf52 , it's always connected to an iPhone, and I need a truly real time respond.
I am sending short messages, like 2 characters at a time, and play a sound on...
Hello, I'm using the nrf52840 SoC, and nrf52840.h appears to be a more "localized" and "specialized" version of nrf52.h for nrf52840. So quite reasonably I should use nrf52840...
Hello, my harddrive went awry and some part of it were damaged (I assume it was file table because a lot of files are affected simultaneously).
So for the past few months...
In s130v2 SDK12.3.0, ble_uart_c, I have set BLE_DB_DISCOVERY_MAX_SRV to 12. Also memory linker is: IROM1: 0x1B000 size: 0x25000. IRAM1: 0x20001EB0 size: 0xBFC0. I use nrf51822xxaa...
Hi,
I have an application where first nrf51822 would act as central, a second nrf51822 would act as peripheral, a third nrf51822 would act as a peripheral. I found that a...
