Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hello Everyone!
I want to make a project that will recognize some tone in the air, up to 5KHZ, and will send nrf8002 a message as a result.
I though to use the nrf52 proccess...
I am using SDK_11 s130 ble_app_gls on nRF51-dk.
An Android phone running nRF-Connect app was able to pair and bond with nRF51-dk. First time doing pairing and bonding works...
Okay, noob alert. I am designing a product that requires a simple iBeacon (redundant?).
I have this hardware on my bench:
nRF51822 Bluetooth Smart Beacon Kit and downloaded...
Hi, I am trying to write a small android app to send direct advertisement to particular device.
i am using 0001 for direct advertisment. But when i advertise the data, message...
Hi all,
In my project i want to transmit and receive one character by using 8051 controller. One is act as full transmitter and another one act as full receiver. In my...
Hi, Nordic and all great guys,
I have a weird and terrible problem about our products,which used a MCU based on nrf51822.
Some info about our product:this is a module...
Hi all,
i am using version 11 sdk.
I want to use 2 nrf51822 board in which one will act as master and other as slave.
MY TASK:
i want to transmit "hello" from master...
I have an NRF52832 Receiver chipset board that detects a tag that is transmitting 10 bytes of payload every second.
I have an attenuator on the board before the antenna...
Dear Nordic Team,
I am using nRF51422 development kit. I am work with example code for ble_pherpheral_proxy.
I want to calculate the battery value from the BLE peripheral...
Hi,
I was checking out the forum and I read that its possible to start a timer from the handler of another timer. However it doesnt work for me.
Im using S132 v2.0.0
...
I have developed my prototype using the NRF51DK and now i am making a custom PCB.I currently use the On booard segger debugger to program the NRF51822.Also, i have ULINK2...
Hi all,
I have been developing a program on mbed using mKit NRF51822 and am now ready to move from prototype to one off production.
I am wondering after i create a custom...
I haven't used printf for a while.
Today I am trying to write some code for UART.
but it can only send the first byte of the string to the port according to the scope, then...
I have the nRF51822 beacon kit, using Keil uVision, downloaded the beacon app and all associated files. Compiles, but how to program the beacon board?
I've done two things...
