When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hey all, I'm a beginner to bluetooth,
I ordered the NRF51822 dev kit and it worked easily out of box with my android phone.
I'm creating my own android app to communicate...
Hi Nordic
I want to change mesh-sdk-4.0 LPN example tx output power to 4dbm, including proxy broadcast, mesh packet,
I try to change " RADIO_POWER_NRF_0DBM " in whole...
The Nordic Uart service for peripheral devices has a function ble_nus_init() which takes a callback function in a struct.. Later on this callback function may be called with...
I am doing the project using nrf blinky.
My phone cannot find the nrf52840 . Before this it is ok, but now it cannot discover it . I notice that LED05 is blinking very fast...
Hi guys ,
I am trying to connect thermistor with the ADC pins of nRF.
I use the steinhart formula to calculate the temperature in degree celcius. I used a voltage divider...
I have a development environment using Zephyr; setup and working from the documentation I found for the nRF Connect SDK. I am using SES and am able to debug the provided examples...
I am writing a Windows program to control an nRF52840 using pc-ble-driver, v4.1.1, with NRF_SD_BLE_API=6
I need to do all of the following:
1. Scan
2. Create multiple...
Hey guys (and merry Christmas),
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). I try to receive data...
Hi,
I try to modify ble_app_uart so i can get a feed back from the boar if send something I use switch case for my use case, I'm working with eclipse
here what I do...
I have been working with the thingy91 source code from ncs, I can compile and load the sample app successfully. However I did notice that when I compile the code it does not...
I tried out DFU functionality initially using nRF52840-PreviewDK and UART transport
When downloading an app via DFU, It takes about 6 seconds from the time I start nrfutil...
Hi,
I am trying to make my own border router for Thread mesh network using nrf52840 and BG96. I have ordered pre-certified third party modules. Now How can I interface it...
I can't seem to find a data sheet on the PMIC used on the Thingy91.
The data sheet shows a ADP536x and discussions call out a ADP5360.
I searched the ADI website and did...
Hi all,
I am trying to test the OpenThread protocol by using CLI example.
Path of example is nRF5_SDK_for_Thread_and_Zigbee_v3.2.0_9fade31\examples\thread\cli\ftd\usb...
Hi,
We use the nRF51 (nRF51822) on our products with the S130 SDK 2.0.1. In order to update the BLE application that we developed, we use the bootloader (secure bootloader...
