Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
I am using SDK 15.3 and wanted to ask that if there is a while loop where I can check flags and increment tickers. The program at the moment gets stuck inside
Suggestions...
hello, I have two questions for SAADC of nrf52832 when we use nrf52832 SAADC for voltage measurement.
The AIN0 is connected to the pin to be measured(the voltage is about...
Hello, I encountered the following error when compiling the SDK16.0.0 with keil5.26, how to solve it?
compiling system_nrf52840.c... RTE\Device\nRF52840_xxAA\system_nrf52840...
Hi,
I am using nrf52832 with softdevice s132. The peripheral device is nrf52832 and central device is a mobile app. I want to disable BLE in nrf52832 and I am using this...
Hello,
I have tested the example code of the nRF-IEEE-802.15.4-radio-driver and now I'd like to modify it.
How I can disable the ack? (I tryed this function: nrf_802154_auto_ack_set...
Hello
SDK 15.3.0
4 year old post describing flash storage libraries:
https://devzone.nordicsemi.com/f/nordic-q-a/13821/difference-between-persistent-storage-libraries...
Hello
I try to use this bootloader https://github.com/williamhuang03/STM32F4-Custom-Bootloader on STM32F4 which works well through cable but as suddenly I use Nfr51 as transmitter...
Hello All,
I want to perform an Rx blocking test for my nRF52840 BLE chip which is installed on my custom board. I wan to transfer the packets from device to other, and...
I take the external PWM signal, I directly used the method of controlling the GPIOTE register to be successful.
But I can't achieve the same effect using the program in...
Hello,
I'm using nRF52840( PCA10056 ) of SDK 15.2 to debug long range mode. And I have already followed the steps in thread: https://devzone.nordicsemi.com/f/nordic-q-a...
There was a similar question in the past, but I couldn't solve it by referring to it.
ESB communication between nRF24L01P and nRF52832 (PCA10040) fails. nRF24L01P...
I would like to remove the HEAP in my app to free up RAM.
I removed all explict calls to malloc and family.
I removed all variable length arrays, after finding that...
Page https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.s140.api.v7.0.1/group___b_l_e___g_a_t_t___c_p_f___f_o_r_m_a_t_s.html, link to http://developer.bluetooth...
I am dealing with a strange anomaly on the MOSI line of the SPI bus - sometimes, the first byte of a command 0x84 to the external SPI flash, I get this on the bus (~ 4 MHz...
Hi,
I'm running an app with softdevice v2.0.0 with SDK 11 on an nrf52832.
the app is using gpiote to handle incoming interrupt from another device.
to start handling...
