I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi
I'm using sd_app_evt_wait(); to go into low_power mode. For some reason it coming back , but I can't figure out why.
Peace of code I am executing is;
while (nrf_fstorage_is_busy...
I am trying to print out a string debugging information. But got below error.
No problem change to printf or cast char array name to uint32_t. See first 2 sentence.
char...
I have python 2 and 3 on my Macbook. I can't run nrfutil which I believe is due to the python installation. I need to keep python 3 for other utilities. I would like to run...
Hello!
We're building radio modules with the nRF52840, one with the a frontend amplifier and one without. Both are exhibiting excessive 2nd and 3rd harmonic emissions. ...
Currently, we are testing that 「buttonless DFU + Bonding valid」 in our App.
But After performing F / W Update with DFU, other BLE Service became invisible.(※2)
So, as...
Hi,
I am currently in an attempt of revising an old board, it uses an ANT+ module which is soon going to be out of production. With the nRF52840, if I were to use the ANT...
Dear Sir,
I had a project is lighting the LED matrix, we choose the LED IC is TLC5958 and MCU is using nRF52832.
Now, we have a question is how to change the GPIO output...
Hello all,
I used SDK15 and nRF52840 DK made a long range advertising and long range connected.
I modified the ble_app_uart_c and ble_app_uart example, the long range...
Hi
i am using the sdk 14.0
i am working with sph0645 i2s microphone , i have tested the microphone and it is working fine with the nrf 52 on 912600 baud rate. Now i wan...
Next week, we have a meeting with our customer to give them an overview on all our BLE solutions (they are interested in module) but I also want to give them an overview on...
nrf52832, SDK 15.0.0
I develop the project based on the example 'ble_app_buttonless_dfu'
But when I want to add some peripherals, such as SAADC, SPI and PPI, and some...
I'm seeing strange corruption in the nrf52840 virtual COM/UART (the one that goes through USB and the JLink interface MCU).
The nrf52840 is running the UART serialization...
I had setup nRF sniffer with below software and hardware, but the Wireshark seen unable capture BLE data.
nRF Sniffer software nrf_sniffer_2.0.0-beta-1_51296aa.zip ...
