I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
Are there any native RTOS build-in the SDK? If I need to develop a sensor device driver (i2c based) any recommendation as the safest way to do that. Choosing between freeRTOS...
Hi,
there is a broken link on https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15-2-0/ble_sdk_app_buttonless_dfu that refers to " Generating bootloader settings...
I'm writing a production script that uses nrfutil to do OTA DFU for both nRF51 and nRF52 radios. I'm using a PCA10059 with nrfutil version 3.5.1.
It works fine for an nRF52...
Hello,
I am trying to use IAR examples to debug some of the examples provided in the SDK.
I am only using examples that support the pca10059 dongle.
One example is the...
Dear All and @rogerclark,
From the release note of nRF5 SDK v14.1.0, Segger Embedded Studio (SES 3.30) IDE has been supported originally.
I use MacOS, and I has set...
I need a help to create a mesh where two nrf52 dk are connectred in the mesh and one node sends a message and another node recives it and sends to a url
I am currently looking at how to put the nrf52 development board to sleep (and wake up) by sending a command from an android application (with SDK v15.2).
I have been experimenting...
Hi
I am trying to establish communication between a NRF24L01+ and an NRF51822, but unable to do so. I am able to communicate between 2 NRF24L01 + and also between 2 NRF51822...
Hello, I'm quite new to both the nRF52832 and the Segger Embedded Studio. I have a college project which involves I2C communication with 2 slaves. I was finally able to set...
Hello,
I am trying to read data from a sensor through sensor TX pin connected to RX pin of nrf51822. Nrf51822 recieves this data through RX pin and sends it via bluetooth...
I am seeing a problem using the nRF52 SAADC with two analog channels enabled in scan mode.
Essentially, channel 0 is measuring an analog signal with gain ~= 15 while channel...
Hello,
I am trying to get the RX interrupt to trigger on the PCA10001 board using the segger debugger as my serial terminal.
My hardware setup consists of a PCA10001...
SDK: v15 SoftDevice: S132 Chip: nRF52832 on BL652 Module
I have a command->response type system. The Central (Android phone) sends a command, and the Peripheral (nRF52 device...
Greetings!
I am using nRF52, SDK14.2, and NUS with MTU = 64. I want to transmit 1000 byte string over BLE upon reception of any character to "nus_data_handler" I have divided...
