I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello,
I was trying to load code in pca10028 and I started getting error as "No cortex M Sw device found".
It was working properly but later it started showing me this error...
Dear Nordicers,
I have an application where node based on s132 sofddevice 4.0.2 has multiple connections as a peripheral and as a central. The case is about non overlapping...
I have an NRF52832 DK [PCA10040, V1.1.0]. It used to do programming with it, but now it suddenly stop detecting as "JLink" in Windows, Linux and Mac. Now when I connect it...
Hi, I use the twi_master_using_app_twi_pca10040 (SDK 12.1) to test the TLC59116 LED module .
By changing the example project's code by referring the GitHub code, I have...
Hello the Nordic Team,
I come here after a lot of research and testing and do not understand what is going on in my program. (is it Embedded or iPhone nRF Toolbox side...
hi,
I follow the pwm routine, 51822 can work and output pwm, when I want to change the frequency of pwm encountered a problem, the program reset.
I use the method when i...
Hi,
I'm using Nrf51822 to implement a RTC(200ms tick)
I connect a external 16MHz crystal to the MCU.
I use the S110 softdevice with BLE function enabled, so it's in ble_stack_init...
Hey. Has anybody played with autocomplete for command line interface.
I like it alot and it is very helpfull. Now a autocomplete would be cool!
Here is what comes to mind...
How to setup a nRFDK52 as a central and nRF bluetooth kit as peripheral. Should I use nRF go studio? Do i need to load the soft device first before loading the app? What is...
I want to store two floats and one 8 character string in fstorage.
I solved it by using 4 uint32 types stored in flash, I got it working in the ble_app_template example...
Good morning,
this is Algocraft (www.algocraft.com), an high tech company whose core business is to develop, design and market a wide range of professional systems dedicated...
Hi everyone,
I'm using a custom wrapper ( github.com/.../arduino-BLEPeripheral) with softdevice S130 v2.0.1. I've extended the wrapper to allow simultaneous advertising...
I am trying to implement a simple example with custom profile by building upon
the tutorial given devzone.nordicsemi.com/.../
My profile is something like this:
Service...
Hello,
My application perform reset periodically. When It does a reset the bootloader need to initialize the softdevice with SD_MBR_COMMAND_INIT_SD before calling sd_softdevice_vector_table_base_set...
Good times,
So I finally put in the tweak to enable the GPIO 9&10 pins to be used for GPIO instead of the default NFC mode. Must remember that reset for it to take effect...
