Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi all,
i want to add a cts service to my project.
i started with ble_cts example of sdk 11.0, but it's not clear what is the correct procedure to do it.
I add the service...
I tried to add a dfu service to the SDK 11.0.0 ble_rscs_app by following the procedure here . I was able to successfully compile and run the application, and when Master Control...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
Hi all
We use the nRF51822 with the S130 V1.0.0 in the peripheral role and a Galaxy S5 in the central role. As soon as the S5 connects to the nRF, we send a connection...
Hello,
I have been working on a customised Nordic Board ,and I can't be able to do a DFU. The DFU App_dfu_dualbank doesn't display the DFUTarg Bluetooth profile on the board...
Yo man,
I use nRF52 with ADC fun in SDK11 and I want select ADC input to internal VCC.
I modify like below:
static nrf_drv_adc_channel_t m_channel_config = NRF_DRV_ADC_DEFAULT_CHANNEL...
Does the Bluetooth Peer Address of NRF51 Chips change randomly [every 15mins] or does it remain same?
When implementing whitelisting for secured connection, it is required...
Hi, I am unable to build this example in Keil Uvision5. I am getting following error:
"no source": Error: #5: cannot open source input file "......\main.c": No such file...
Hi,
I am trying to setup a testing environment using nrf51-ble-driver_win_0.5.0.
All of my job are:
Download nrf51-ble-driver_win_0.5.0, and program connectivity_115k2_with_s130_1...
Recently updated to SDK11 + s130 v2.0.1 on an nRF51822 xxAC LFCLKSRC=RC
BLE Advertising no longer works. Localized it to our use of TIMER2 for an implementation of systick...
Hi,
Im trying to connect MCP25625 via SPI on nrf52. I checked with the scope that CS, MOSI and SCK are correct, but I get no reply on MISO line whatsoever.
I perform a...
Every time I want to connect to Nordic ble device from my Phone, it ask for pairing confirmation and then it create bond. That's how it should be.
But if the device is...
I'm using nfr52 with softdevice s132.
I want quickly perform flash write during power loss.
When I realize write using fs_store() I obtain time more than 5 msec.
How can...
Just do
NRF_POWER->SYSTEMOFF = 1;
in main()
and found if it's boot by powerup
the current is 10.4uA~10.5uA
and if a re-flash the hex, the current is 1.4~1.5uA
...