Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I'm trying to use winbond spi flash (w25q64fv)
but i have a problem with spi as you can see in below image clock stop before receiving data from spi flash, do you...
Hi,
i use for debugging propose JLinkRTTViewer on OS X Terminal. It works fine but i wanted to use Colored Terminal output, like it is possible in windows rtf viewer application...
So I've been using the SPI master driver supplied via the SDK. I'm currently trying to use the nrf51822 to control an LCD screen so I can display some information. I don't...
SoftDevice : S110 7.1
SDK 7.2
Example : experimental_ble_app_uart
Using IAR 7.1
Using nRFGo Studio 1.19.0
Board : PCA10001 V 2.0.0 (Rev. 2 MCU)
Test device...
Hi, recently I'm looking at some computer architecture books.
So my question could be easy or silly.
I tried to search more but I couldn't find many.
The nRF51822...
Since the SoftDevice uses Timer0, am I correct in assuming that the maximum number of PWM channels for nRF51-DK with SoftDevice running is 4? (Two each on Timer1 and Timer2...
Hi Expert,
At my nRF51 platform, I opened two GPIOTE users one of which is used to handle an external sensor interrupt. After invoking app_gpiote_user_register(&sensor_gpiote_user_id...
I am seeing some very strange behavior when using an ANT channel with the sd_ant_acknowledge_message_tx call to guarantee message deliveries between a master and slave.
...
hello I am using nRF51822 microcontroller and KIELuvision5 for programming, I am new to this platform kindly need your help, I was compiling the basic code it toggles an LED...
I tried to follow some tutorials on this site to build the samples for the beacon modules using gcc.
I am seeing this error:
Compiling file: bootloader_util_arm.c
...
I download my elf file using SEGGER Jlink via Eclipse. The instruction pointer gets positioned on the Reset_Handler. But when I try to run the code after that, I get a SIGTRAP...
HI:
I try use pstorage_raw_mode to store data. According to the document description,first steps:
ble_stack_init() and scheduler_init(). Then, in turn, calls the function...
Hello,
I need a FIFO buffer for at least 20 arrays with 8 int32 in each... for use in an algorithm.. is there a more elegant way than just copying them all around each...
I'm using the mbed platform and have been battling hard faults as I try to find the best way to write with high frequency to SPI to update a series of LEDs while still allowing...
