Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi!
I loaded up the LTE Sensor Gateway application on the 9160-DK, version 0.8.5. It crashes at the same point every time. I can see it connect to the cloud. When it attempts...
We would like our device to accept "just works" bonding for the first 2 minutes after power up in order to provide simplicity, but require mitm with oob after this to provide...
I have setup my new Thingy91 and got it connected to nrf Cloud. I can see environmental sensor data in the terminal window but it is asking me to update the modem firmware...
Hi, I am using timer capture function to get the current time when i get the interrupt on GPIO.
But it is not returning correct timer value in seconds (Example: for 2-3sec...
Ok so this is an interesting one.
When I got a new PCB with a MDBT42Q module containing NRF52832 I flashed it for the first time (program and softdevice) all the code works...
Hi, I have started development on nrf52840 .
I want to use BLE as a Peripheral . Can you please suggest me which example I can use for sending characteristics and add my...
Hi everyone, I have questions like this: I'm using experimental_lpn example when I want to connect to the friend node when I get request timeout. As far as I know when the...
We're thinking of attaching a battery in the manufacturing process but they may not be programmed right away. Do empty nRF52 modules go into sleep mode when there is no program...
Hi
how to connect one peripheral to two central and after connection established sent the data to both central?
I am using nrf52, soft device 132 .
i am able to make...
Hi!
The nrf5340 PDK I've purchased does not have a mounted "nRF USB" (J3) port, only the debug (J2) port.
Is it possible to do raw USB communication with the USBD driver...
Dear Sir.
I am using the Timer of nRF916 .
In a simple project the timer is working fine ( see attached code ).
A buzzer is connected to PWM output pin 12.
I can...
Dear Sir.
Attached a code .
It takes about 20 seconds from power on until the Blue Led is On.
The timing of the Blue Led is about 2 sec , as in the code.
Commenting...
Hello
I use sdk v17 and nRF52DK. I want to use mpu6050 sensor in the example of ble_app_uart. SDK provides a driver for mpu6050, but I am not good enough to use it.
https...
Hi, I'm a beginner with these Nordic DKs. I'm just trying to connect it to my computer and get familiar with the hardware and firmware. However, when I plug in the DK via...
i want to store and retrieve data in flash. i followed steps as in the sdk infocenter but i am not getting the interrupt after fs_store(). Actually return value of fs_store...
