Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Building ‘secure_dfu_secure_dfu_ble_s132_pca10040_debug’ from solution ‘secure_dfu_secure_dfu_ble_s132_pca10040_debug’ in configuration ‘nrf52832_xxaa_s132’
Linking secure_dfu_secure_dfu_ble_s132_pca10040_debug...
Hello,
I'm trying to update the SoftDeivce used on our product from s140 v6.0.0 to 6.1.1, but am running into issues. Per the release notes it sounds like no updates / recompilation...
we use 52810 connect with iphone6, then read the RSSI value, it will disconnect with the iphone6.
reconnect the iphone6 and read the RSSI value, it disconnect again.
we...
After doing some reading, I realized that the light CTL server model does not contain the generic OnPowerUp set message. It is contained within the light CTL setup server...
After import a project in to SEGGER and included paths of header files
While compiling i got the error like below
sorry, unimplemented: non-trivial designated initializers...
Hi, I am using a system where I am using nrf52832 nordic chip. I generate a custom ble service using this ' https://github.com/bjornspockeli/custom_ble_service_example ' github...
Hello.
I would like to use the SPIS module on the nRF52840 DK. I configured it by following the examples given by Nordic.
When I use pins P0.14 (nCS), P0.15 (SCK), P0...
I am using now SDK 15.0 and the value of APP_ADV_DURATION is set to 18000 (180 sec)
But I saw that fromSDK15.2, it is recommended to change the value to 0 in order to get...
Hi,
We are running an application using REG1 only in DC/DC mode, REG0 is disabled. I believe we've found a small issue with our decoupling of all the power pins, but I'm...
Hello,
I am trying to connect my nRF9160 but am running into some trouble. Only LED 3 blinks for about 3 minutes and then just stays on without blinking; LED 4 never blinks...
Dears
I double the ble_nus_init as below ,I can get 2 service bouth have 2 characteritic.
as below:
err_code = nrf_ble_qwr_init (&m_qwr, &qwr_init); APP_ERROR_CHECK...
I am facing issue with programming of own developed nRF52810QFAA board. I used Pins 25 (clock) and 26 (data) along with Vcc and Gnd to flash device. I tried with two boards...