I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi am using NRF52 board ...and am trying to send data(which is not a string) using ble_bus_string_send . I send data only once from a one second timer but the other side is...
Hi all!
I'm working on an nrf51822 (technically right now I'm using the PTR5518 as I'm still prototpying), and trying to set up a voltage divider on my pcb in order to...
Hi,I am debuging my programm base on SD-110-V6.0.0 ,sdk-V5.2.0. When I use the
static void characteristic_disc_req_send(const ble_ans_c_t * p_ans, const ble_gattc_handle_range_t...
Hi everyone,
I have a nrf51-dk. I am running Master Control Panel app on my win7 computer. However, I cannot see my nrf51-dk in discovered devices section. Log says, Loading...
I am working on an application for the nRF52 Preview board, using SDK 0.9.2. I need to acquire about five analog samples from a single channel at roughly 100 Hz, then wait...
I use SDK9.0,SD8.0,the device is 51822AC,the device can enter to Bootloader mode.
As it shows below.
Then I selected the .zip file to start DFU
But when it reached...
I'm trying to do all my development on linux, mostly so that I can use a continuous integration environment. I'm setting up a server to compile my firmware app on every pull...
Hello I am currently using the NRF52 DK2 PCA10040 with S132 soft device (nRF52 SDK v0.9.2) . I have setup my code to sample 4 analog pins periodically. I configured double...
Hi everyone,
Well, our device is based on NRF 51822 CFAC MCU. It’s an ibeacon based device which advertises and receives data frequently, and writes data into flash memory...
Hi,
I have a project that uses PStorage and the Nordic UART Service. PStorage is used to store a variable that is updated by the device, irrespective of the Bluetooth,...
Question:
From ble device I have to send some data or character to mobile in connected mode. After sending that data the device is not going to sleep mode while connected...
I'm trying to modify the beacon properties of the nrf Beacon in the nRF Beacon APP but it doesn't allow me to change those properties.
If I use the Beacon scanner the device...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi, I tried it from my Nexus 5, using the Android version of MCP. I can connect/unconnect, detect link loss, and (apparently) everything else, but only LED 1 seems to behave...
I want to connect one peripheral to a few central devices (lets say 3) but the central devices don't need to be connected to the peripheral at the same time. Should the PERIPHERAL_LINK_COUNT...
