I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
I had some issue with my nRF52 DK PCA10040 v3.0.3, The programmer was totally unreachable also with the simplest terminal command so I tried to reprogram it trough hidden...
I am trying to implement GPS code in the nrf9160 but I cant find the function nrf_modem_gnss_init(); to initialize GNSS inside the modem in , is it being initialised within...
The following log is a compilation error.Is there any way to correctly compile?
e:/nordic/ncs/toolchains/fd21892d0f/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr...
We have an application where response time is critical, and we are trying to minimize the time from advertising to an active channel sounding session.
What we have already...
Dear Nordic,
We are currently evaluating the Amarisoft CallBox as an end-of-line (EoL) testing tool.
In an ideal scenario, we would like to use 1NCE production SIM cards...
When performing FOTA using NCS 2.9.2, we observed that the swap using move process takes approximately tens of seconds. However, with NCS 3.2.4, the same swap using move operation...
nRF Connect SDK v3.2.3, nRF9160.
Hi,
I'm working on a project which has MCUBoot enabled (dual slot) for firmware updates over cellular connection. I did not have a pm_static...
Hello,
I want to program the bare nRF52832 MCU over SWDIO, SWCLK, GND and +3,3V Connections with a Segger J-Link programmer. Unfortunately the programmer could not connect...
We are experiencing an issue with the QSPI driver on nRF54L15 where external flash access stops working after a BLE bonding procedure.
The system works correctly until bonding...
Is it possible to be able to get hold of some of the legacy software for the nRF52 BLE sniffer that works off the old nRF Command Line Tool rather than the nRFutil? As I'm...
Hello together!
I am trying to reproduce the ultra low power connection as described in this whitepaper: /cfs-file/__key/communityserver-discussions-components-files/4/3482...
Hi,
I am working on a smartwatch PoC using the nRF7002 DK (nRF5340), and I am trying to interface a 1.8" ST7735 SPI TFT display (128x160).
Hardware: - Board: nRF7002DK...
Ultrasonic welding is commonly used to seal plastic enclosures for electronic devices. 32kHz crystals can be damaged by this type of welding and manufacturers recommend not...
Does APPROTECT supersede SECUREAPPROTECT or do both need to be enabled for maximum security?
Similarly, do the HW protections (APPROTECT, SECUREAPPROTECT, ERASEPROTECT)...
