Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
Why I use the function m_device_state_set(cons, PM_DEVICE_STATE_SUSPENDED); to close the serial port is still a large current:38.80uA?
The verification method is as...
Hi there
I wrote SDK 17.2 ble_app_hrs to the module.
When connecting to an Android device, Empty PDUs will no longer be sent. I checked the RTC COUNTER, but it is incremented...
SDK: NCS 1.8.0
Based on: Peripheral LBS example
Central: Mobile (iPhone)
Peripheral: nRF52832
Hi,
We are in the process of adding FOTA to our custom project and...
We are using nRF52833 with DFU secure bootloader and implemented DFU master/host on ESP32 BLE. We observe that DFU bootloader get stuck in above locations in softdevice more...
Hi Nordic
I have been using your example on USB MST to embed it into my application
Everything works ok, but in the main loop im constantly polling for USB power event...
I'm looking at the nRF Connect SDK Matter documentation, and the intro page states :
"If you are new to Matter, check also the tutorials on DevZone ."
The link in...
I am using nRF5340DK and would like to send and receive data to computer via UART1 and pins "TX", "RX", "CTS" and "RTS" using USB TO RS232 SERIAL CONVERTER.
This way I...
Hello Nordic, I have a problem. I'm running the nRF9160DK with three sensors and an sd card reader. The three sensors and the sd-card reader are connected via SPI. Due to...
Hi,
I would like to generate interrupts triggered by an input clock pin at 2 MHz to sample an 8-bit digital signal. I am trying this with an nRF5340. Up to this point...
Hello,
I am working with a nRF52833 and I am no longer able to use my JLink Base to flash it. I was previously able to flash it and there was no hardware change at all and...
Hello,
I am writing code in zephyr on nRF52840. I am advertising my BLE. and we have a stable android app (built-in a flutter). My problem is when I am trying to write an...
Hi teams,
Recently, during my test with some Arduino-Shield compatible daughter board with nRF52833DK, I found some pin mapping is incorrectly defined in nRF5 SDK.
The...
I have multiple elements with multiple sensors (4x6 in total, all 4 elements has the same type of sensors). I need to find out which element called sensor get callback. In...
