I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hello,
I am trying to change the tx power for my nRF52-DK which is having nRF52832 chip. I trying the following code to change the tx power to -40 dB.
int8_t tx_power_level...
Is there any example about the dongle nrf52840 act as a central? Is that possible? In that case for a ble connection between dongle and board a service does to be create on...
Hello,
I need to long WRITE AND long READ from a central/client (android) to a peripheral server (nrf52). when I says long it means longer than the MTU.
LONG READ
I...
At the top of the Nordic home page, there's a link for "Bluetooth Software":
Following that takes us to https://www.nordicsemi.com/Software-and-Tools/Software/Bluetooth...
Hi!
In a Bluetooth mesh, we would like to get a feedback message from a group of nodes, via a reply message, after sending a message to the group.
The Bluetooth blog writes...
Hi. I am trying to get the peer address from of the peripheral my central has connected to within the BLE_GAP_EVT_CONNECTED event.
The following returns the address, however...
Hi folks,
I try to do create timer. Therefore i want to adding some files in blinky project. So here is some screen shot. Thats about debug error. First i used SDK 15...
Hi team,
I was asked by one of my customers, that if they can use nRF51822-QFAC (existing products design) as peripheral while connected by 2 central (Phone & Router)...
Hi I am a fleding embedded system engineer trying new ways to develop a process( Flashing) in my company,
My company's senior software has designed a control box which...
Hi,
I am facing problem while developing code for the application.
I am working on the "ble_app_uart" example code to develop my one of the application, But after making...
I'm using the code from Vidar supplied here . It works well, but shuts off after 3 minutes.
Based on the idle_state_handle brief, " If there is no pending log operation...
Hello,
I would like to touch on some problem we encountered when using the MPU9250 sensor.
Our goal in the project is to simulate the movements of the MPU9250 sensor in...
When I use the nRF connect app on android phones, the services and characteristics can be detected and controlled correctly, as below.
But when I switch to iOS nRF Connect...
I am using the nRF5_SDK_15.2.0_9412b96 for development of nRF52840. I have both the nRF52840 dongle and also the DK.
I find that I am not able to change the default Nordic...
Hello. I have build by application on nRF52832 based on ble_app_template example (SDK 15.1, softdevce s132 6.1.0). I've configurated Peer Manager library as it recommended...
