Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hello,
i'm trying a bluetooth connection between nrf UART v2.0 installed on my phone(android 4.4) and nRF 8001 (i'm usign nRF2740 card). My microcontroller is a STM32....
Hi.
I made my own board using nRF51822AC.
I want to connect this board to PCA10028.
There is Debug OUT port(P19).
Net names are EXT_VTG, EXT_GND_DETECT, EXT_SWDIO, EXT_SWDCLK...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
Example code is using "ble_db_discovery_start()" function to discover peripheral.
In this function, there is "SRV_DISC_START_HANDLE...
Hi. I'm using PCA10028, SDK10.0.0, S130.
I'm testing External interrupt.
Current concumption was just 50uA around(low speed advertising mode).
But It goes 1mA around...
Hello
I'm working on a network of nodes with more than 300 nodes
each node is constructed by (1 arduino nano,humidity sensor, 1 relay and NRF24L01 +)
I'm working with the...
Hello. I'm trying to understand twi_sensor sample code on nRF51. (nRF51_SDK_10.0.0_dc26b5e\examples\peripheral\twi_sensor)
I have a trouble finding where the function twi_handler...
Hey,
i've bought the nrf52832 Preview DK some time ago, are there any big changes to the new DK? So if i buy a new nrf52832 IC i can desolder the old IC and use the new...
If I have some value and this value has become out of desired range I want to change property from indicate to notify.
I only found function sd_ble_gatts_characteristic_add...
I'm developing an application for a device which needs to support both DFU and some method of restricting connections to a single central (ie: bonding). This is a challenge...
Hello!
Is there have any tutorial for how to create GATT service on the MCP(master control panel app) and what coding do we need to add to the project?
Hi, I would like to put a nrf51822 device into system off mode and wake it up with a GPIO transition from high to low.
I would like to measure the press time of the button...
I'm using JLinkExe ( J link commander ) for Linux to flash the application firmware on NRF51822_QF_AA target. The following have worked so far, but I'd like to confirm and...
Hi,
I am upgrading to SDK 11.0.0 and S130 v2.0.0 from SDK 9.0.0 and S130 1.0.0 and I am stuck with an error when I call sd_ble_gap_adv_start. Here's the code that now fails...
