I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi, I'm a beginner for nrf52840 development.
As I know the ARM core operates on 64MHz clock.
So I think there is 64 MHz clock in this board.
My question is the...
Hello everyone,
I accidentaly flash the Dk when the power profiler kit was plug on it, so now the led are Always off on the PPK, to fix this I have to flash the PPK but...
hi support team,
i have one ticket about 53832 hardware problem that is resolved:
devzone.nordicsemi.com/.../52832-p0-25-and-p0-26-problem ,
Surprisingly i found out...
Hello,
I have this very strange issue where my code is hanging at startup while reading NRF_UICR->CUSTOMER register when build release code. system doesn't hang in debug...
When I enable and disable UARTE RX my chip consumes nearly 500 uA.
I assume the most of it comes from the "disabled" UARTE RX. Either im not disabling it correctly or thats...
Hello,
When we are trying to create mesh using IOS application latest version(3.2.0) but Mesh doesn't work properly.
But the same system is tested with Android Nrf App...
Hi
I am going through the AWS IoT example using an nRF9160 DK, but having some problems with it.
My setup
nRF9160 DK + LTE-M SIM card
I used this same board and...
Hi,
We are working on adding T-M to our middleware, and we discovered a pretty annoying side effect.
We are using NCS 2.0.0
One of our device is controlled using the...
Hi
According to Case ID: 279868 it seems like there has been some issues with modem lock up on nRF9160.
Some questions:
Do you know if this issue is still valid...
Hi there,
I am developing a central in nrf52840 dk using SDK v2.0.0 in VS code.
The BLE part is OK and it is possible me to get notifications.
Now, I need to store the...
Hi,
I have nrf52840-Dongle and nrf52833DK and it was working all good few days back with my code for BLE-UART (Centeral-nrf52840 Dongle and peripheral nrf52833DK) but now...
I need a crystal capacitor for this two Crystal XRCGB32M000F1H01R0 and SC20S-12.5PF20PPM. The value of this capacitor is 12pf and package 0402 So, please help for selection...
I am using a rotary encoder with nrf52840dk and I am confused about how to run sample QDEC code from zephyr/sample/sensor/qdec on nrf52840dk.
I got this error when i tried...
Hi Nordic Team,
Thank you for your support.
One of our customers got Version 2.1.0 for two.
But it was confused. Box label is 2.1.0. But board was 2.0.0 and both...
