Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi,
I have the following scenario:
nrf5340
SDK 2.1.1
HFCLK: 32Mhz crystal
LFCLK: square wave of 32768 Hz from an external RTC, range [0 - 1.8] Volts
square wave...
Hi, I am using a custom nrf52832 device. In that device , button is connected with reset pin P0.21. due to reset functionality I am not able get interrupt from button.
how...
Hi,
I am using nrf52840 to develop a product. I use NCS sdk v2.5.0.
I developed a project based on the [Bluetooth: Central HIDS] example in the NCS SDK. This example enables...
Hi,
i am using SDK 2.1.1 with nrf5340.
I would like to add the linker option --wrap.
What are the possibilities to add this option in Visual Studio Code ?
Could it...
Hi,
I am using nrf connect SDK 2.9.0 with nrf52840DK and MCUboot with own RSA .pem file (from older versions, so no ECDSA possible). How can I increase verbosity when building...
Hello,
My BLE peripheral code works fine with Android devices, but it is failing with iOS devices. I am encountering an error message: "Ignoring data for unknown channel...
I'm working through the tutorial here. https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals/lessons/lesson-4-serial-communication-uart/topic/uart-driver/#uart_config...
I'm working with nRF52840, my function will read wav file from SD card and play it using Zephyr I2S driver. My source code about playing sound in below.
The strange is the...
Hi,
For a meter application with battery, I want MCU is sleeping but comparator still working to count a pulse input (freq <100khz)
Can Nordic IC can support this idea...
Good day. I'm working on a custom board that uses nRF5340 as the main MCU with a WIFI module, nRF7002. The nRF5340 and nRF7002 are wired based on the nRF7002DK. When I uploaded...
My project as above.
I'm developing my code in nrf52832,with nrf SDK v17.0.0.
I try to add some customized params by FDS so that I can get them after the next run.
The...
Hello,
I am having trouble reading an interrupt on an nRF5340. This is on a custom board using the ISP2053 SIP.
We are using the high speed SPI interface on pins P0.08...
I'm unsure if this is the correct place to post since this is not a Nordic-specific issue.
I am using the P100 which is a nrf52840 connected to an HL7800 through a UART...
hi all
i want to use a chip antenna for nrf52840
but un data sheet there is not any sample layout or component details
for example i want to use this chip antenna
...
