Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
In our custom board we checked WIFI, facing below issues, 1. We flashed sta sample project to our custom board facing the issue below. Is there any configuration needed to...
I am using Asynchronous API of uart to receive the data. During the reception I face UART_ERROR_FRAMING issue in UART_RX_STOP event. But after getting that too it enables...
I use the nRF52840 development kit. In this Board i flashed the ncs zephyr sdk v2.6.0 sample code for system off and device going to sleep.
i Want to wakeup the board from...
I made an assumption that the nRF52840 Dongle has the ability to communicate via UART as most boards I worked with have this feature. This seems not to be true, but I don...
Hi
1. How to set PWM power-on state to Low level in ncs v2.4.1 2. How to configure the dts file so that the corresponding I/O port is in the low state when PWM is powered...
Hello,
I am after an example for nRF5340 showing how to use RTC to wake up from sleep.
I have a couple of timers running few tasks at regular intervals in a forever loop...
new to nordic and keil need help compiling custom project
currently my main file only works with the nordic 1822 series processor and in your example.
I need to have it...
I cannot find a specification for the SAADC converter's reference accuracy. The product specification indicates it is 0.6V, but beyond that I cannot find anything. Looking...
Can we run our Customised Bluetooth Host Stack on nRF5340.
Please provide us with sample Brinup Code for Bluetooth Controller.. Send HCI Reset and Bringing up the Controller...
We need to retrieve data from an FPGA to the nRF5340, process it with the network and Wi-Fi protocol stacks and then send the data to the nRF7002 for Wi-Fi transmission. We...
Hi!
Currently I have the following application requirements:
Use SPI peripheral to communication with FPGA device. ( NRF5340 [ SLAVE ] <---> FPGA [ MASTER ] )
The goal...
i'm trying to read voltage signals from a sensor using internal ADC.When the input is not connected,there will be noise. I use differential input pins like this:
NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_DIFFERENTIAL...
Hi,
i need to store few configuration bytes in non volatile memory. I found out there is settings module that can be enabled in Kconfig GUI (SETTINGS option).
My use is...
Hi,
I have successfully programmed the nRF5340 Audio DK as a gateway device using the Command Line Tools and by using the directives listed in the 'nRF5340 Audio' program...
I'm working on adapting ST's RFAL NFC library for ST25R3916B/X-NUCLEO-NFC08A1 on an nRF5340/DK in order to emulate an NFC tag, and have run into an inconsistency I'm hoping...