hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi Guys,
We have schematic of future NRF 51822 project, who can help us with PCB design? Or who can suggest me where i can do it?
PCB.DXF
schematic.pdf
Hello All,
I am trying to build a BLE peripheral project with RTX OS which is using S110 Soft Device and bootloader is also there in Flash memory region. So when I am trying...
I am just beginning to develop with BLE.I came across the nRFgo Studio through Nordic and BDS through the bluetooth SIG.
1]What are similarities/differences between the...
Hi.
I want to active HW timer with SoftDevice 7.1.0 .
Timer operation is good but I can not stop the timer.
The power consumption is 200~300uA after timer expired ( or...
Hi,
We would like to use NRF52832 chipset for our project, and we need to configure 11 pins as GPIO interupt , Is this possible ? How many pins we can have as interrupt...
I have Bluetooth iOS app communication with my nRF51822. I notice that when I connect the the nRF, the first GATT write event is always the same:
p_ble_evt->evt.gatts_evt...
I am using SDK v11-alpha2 and following the BLE Services and BLE characteristics tutorial.
When calling sd_ble_uuid_vs_add as the Characteristics tutorial asks, I get a...
HI ,ALL ,
i have change the project for the purpose of enter a six digit key at cellphone side to enable the notification with the board(52382).
But when i input the...
Hello, I looked througth the devzone but didn't find direct answer. So created new one.
RM v3.0 states chapter 12.1.19 "Reset behavior" with table. However, it is not clear...
Hi,
I have to check every 10 minutes the battery level when BLE is connected .
I have found in this forum this source : github.com/.../main.c
As the source date is...
Hello All,
I developed one project in nRF51822 with S110 Soft Device based on following configuration.
SDKv10.0.0
DFU capable
RTX Support
And now I want...
Hi ,
I am using Soft Device S130 and NRF51 kit PCA10001. I am using SDK 11.0.0-2-alpha .
I am trying to test the Alert Notification Service Example as mentioned here...
Hello!
I'm trying to use the nRF51422 internal ADC to send the value over BLE then monitoring the value received on the nRF Master control panel on Android phone but I...
