According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi,
When I tried to use BLE5.1 phase data to achieve direction finding, I found a phase shift between reference period and the first slot, as the below graph shown:
...
Hi DevZone!
I would like to use nrf9160 for sending/receiving data by interfacing it with my microcontroller over UART and sending AT commands. I have a nrf9160 Feather...
Hello, support team.
In my SDK, I created two app timer.
What I expected is
- 1st handler called every 1 msec.
- The other handler called every 100 msec.
But...
This "BUG" is observed on nrf52840 DK (chip version is version 2 from *(UINT32*)0x10000134UL).
When NRF_RADIO is set to TXADDRESS 0 and RADIO_PCNF1_WHITEEN_Enabled...
...
Hello,
I am using VS Code 1.48.2 and building the C++ application code on nRF52840 dev board using "west" commands.
I have the following structure
project_directory...
Hi,
With the latest SDK (17.0.2) I try to use the SAADC module in blocking mode but when I call <nrf_drv_saadc_sample_convert> an ASSERT is always triggered in <nrfx_saadc...
Hi. I'm developing central device for IoT system.
Everything is going well, but there are some problems on connection precedure.
I tried to conenct 7 pheriperal(nRF52832...
Hello,
The question is really this - when using DECODER.LOAD=WaveForm mode, do I have to provide all four values even if the outputs 1-2 are not used? Or will it suffice...
Hello all.
I need to detect when data is received on RX. I am planning to use it with PPI channel so i could instantiate a task to it.
I tried to use nrf_twi_event_address_get...
Hello,
I need someone to shed some light on how to use the 'reg' node property because I am confused.com .
On this page https://docs.zephyrproject.org/latest/guides/dts...
Hi,
After a connection long push event does not work! But before a connection long push works fluently.
I could not found the error.
Thank you for your interest.
...
Our group is trying to use the NRF52833DK do phase-based distance estimation as described in the attached paper. To do this we want to transmit packets with constant tone...
Hey There,
I have one problem more. With my .cs Script I am opening a USB Port on my Raspberry, to communicate with my Nordic Thingy 91.
I can Read what the Nordic is...
Hello,
I want to read the CA certificate stored inside the modem, unfortunately the modem_key_mgmt_read function cannot read a certificate bigger than 2kb even if CONFIG_AT_CMD_RESPONSE_MAX_LEN...
I have a few nRF52840 DK to evaluate a Bluetooth mesh application. The light switch example is ideal for our initial tests. The only thing I would like to do is to write some...
