I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi guy,
I am new to nRF52, I read some example code and I see this:
#define SPI1_CONFIG_SCK_PIN 2 #define SPI1_CONFIG_MOSI_PIN 30 #define SPI1_CONFIG_MISO_PIN 4 #define...
Hi there,
I'm currently working on a project in which I need to be able to deactivate Bluetooth advertising at the press of a button. I am using SDK 15.3 and have built...
I am using the database discovery module in my app (my code is based on the "HRS client" that is one of the SDK examples). I am able to discover multiple services (both custom...
To the kind attention of Nordic support team,
I have got legacy nRF24 gzll devices that are supposed to communicate with new nRF52 platform. Sometime it happens that nRF52...
Is board support available for Thingy91 "nRF9160_PCA20035" board in Segger Embedded Studio? I am not seeing "nRF9160_PCA20035" as a supported board under "ncs\zephyr\boards...
Hi,
In our project we want to use nRF52832 chip using HCI Command interface. We are trying to use Zephyr RTOS project for geting HCI interface through UART. We are using...
Hi, I using the 15.3 SDK.I want to get the peer's name by filtering Company ID(manu data).The Company ID is in the scan response packet, and peer's name is in the adv data...
Hello!
I would like to use an external antenna with my nrf9160dk to be able to attenuate the signal. But I am unsure about what is needed to make it work.
Is it enough...
Hi,
I have read through this tutorials on how to develop custom UUID, and I have implemented it successfully.
But I need to have 2 characteristics. I have basically duplicated...
Hello. I am trying to use TWI with mpu9250 sensor after System Off mode. But it is not working well. Do I need to do some preparation before going to System off mode? Where...
Hi All,
I'm using Ellysis sniffer for debugging my ble mesh network.
I've made network setup using generic on/off application and I'm able to communicate and capture...
I have a nRF9160 DK and since I am in Germany, we are trying to use the most common LTE band they use here, which are:
Band 1,3,7,20
However, band 7 does not seem available...
When I compile one of the nfr_log modules (e.x. nrf_log_frontend.c) I get the following error.
I do include ../components/softdevice/s132/headers/nfr52 in my User Include...
I have an nRF9160 DK which came with an enclosed eSIM from iBasis, that is supposed to work in most of Europe.
However, after jumping through all the getting started hoops...
Hi All,
Posting this here after a lot of searching and troubleshooting. There have been a lot of similar posts but none actually seems to go into how to implement this in...
