Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hello
I used to do TWI communication until now, but it was decided to do sensor reading with SPI communication by changing the sensor.
So that's a question,
What is...
Hello,
I am wondering that when BLE5.1 SDK will be available ?
Is there any possible ways to test your BLE direction finding solution ?
As far as I know, development...
I want to set a keep alive value of MQTT while eDRX is enabled, but it doesn't work well. Any advice?
Environment - hardware: nRF9160 DK 0.8.2 - firmware: 0.7.0-29.alpha...
Hi,
I am using nRF52832 SOC along with SDK v15.2.0 with custom hardware, currently I have requirement to use DFU protocol in BLE application to get a FW of another sub system...
Hello, I hope your day is full of the scent of flowers.
I am in the process of the Ble_Cnetral and PrePhereal project.
I have added and built the Uart.
Why is...
Hi frnds,
I am using the ble_central and ble_peripheral code (nrf52840).
i am sending 400 bytes of data to central from peripheral continuously, sometimes the boards get...
3.19 [78] TIMER: High current consumption when using timer STOP task only
I'm using app_timer_stop. But I do not know how to cope with this errata. Does the timer stop that...
Hi
After upgrade modem to mfw_nrf9160_1.0.0.
Most of our SIM cards still working good on both AT and MQTT projects.
Two of our SIM cards can't connect to LTE when uses...
Hi,
I'm using nRF52840 where it's written 1.0.0 on the jlink ship and QIAAC0 on the nRF ship.
When reading the info.variant register I got 0x41414330 which is ..AAC0...
Hello everyone,
I am using a NRF52840 development kit to write a custom protocol, so for the moment I am not using the softdevice but I am rather using the Radio as a...
We have a board built with the NRF9160 and an ADE9153A. The ADE9153A only responds to messages with odd parity. How do we set the NRF9160 to odd parity?
Hi,
I want nRF52 Continuous Unmodulated TX carrier.
Is it possible by TASK_TXEN and TASK_START or radio_tx_carrier command of radio test example, after TX configuration...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Hi, team I am trying to build a system with one master and multiple slaves using the mesh SDK. ( This is similar to the light_switch example. ) At this, I want to give each...
