The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi everyone,
I have a device which can be a gzll host or BLE, depends on what software inside, and it is based on 51822. And now, I would like to combine this two function...
Hi,
I know that the NUS service ble_data_send() can send string and integer data via BLE to an app, but can it be used to transmit 24 bit float data ? If not, what other...
Hello,
I'm very new with the DFU on nordic and I would like to know if it is possible to upload a valid application so that my DFY can jump onto it ?
Thank you in advance...
Hello,
I'm very new with nordic environment. i would like to modify the FDS address because it seems it is always put to the end of the flash and when i flash a new bootloader...
Hello,
I'm flashing a bootloader (DFU) and then i'm flashing my application but each time i flash the application, Segger Embedded reflashes the softdevice and the MBR....
When building the sample code using the latest SDK I do not see the device in the device manager and after a while I get this error:
Any hints on what is wrong ?
...
I have already made a post for this problem. Initially, Amanada Hshei gave some troubleshooting techniques and it did not work out,
Here is the original post, and My request...
Using Windows 10
Master Branch
Compiled using Segger 4.16
Downloaded merged.hex
When running NRF Connect Link monitor and connected to nrf9160
I receive the following...
HI,all
I have tested ZC and ZED to establish network,I found a method zigbee_erase_persistent_storage(bool),when i put true on ZC and put false on ZED, first time they can...
HI,all
I am a newman for zigbee on NRF52840 with S140 softdevice,
I have two board, one is ZC and another is ZED.
On ZC board, I use ZB_GET_OUT_BUF_DELAYED2 to send...
I am using sdk15.2.0 with PCA10040 dev board.
In ble_app_eddystone example, the configured advertising interval and duration dont match the observed values.
I think I...
Hi Nordic,
I have recently received an error from pm_init that I have never seen before, NRF_ERROR_INTERNAL. After some debugging, I found it was really due to NRF_ERROR_STORAGE_FULL...
Hi,
I am using NRF MESH SDK V3.0 ,nRF5_SDK_15.2.0 and with s132_nrf52_6.0.0_softdevice .
I've noted some problems when i try to use the app_timer in repeat mode with a...
Hi Team,
I transplant the project Uart from example/peripheral/uart tranplant to blecentral/multilink project, but it does not work, it indicate that APP_UART_COMMUNICATION_ERROR...
