Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Recently got my Nordic Thingy:52 which is based of nRF52832. I wanted to test sending the data to cloud, so I just followed the IFTTT tutorial on the Android Nordic app. I...
For a design consulting client, they have a startup problem and need to know the approximate leakage current when a GPIO is in "DISCONNECTED" state.
I know the NFC pins...
I am using Uart Ble example of sdk , i want to write to Tx without UART can u please help me do it
i actualy want to send accelerometer data which is of size 40kb after...
Hi, I have added BLE custom characteristics in my application. I am writing and reading some values through ble scanner mobile app. Here i observed that when i enter string...
Hi,
I trying to use higher MTU size for my application and i have followed the att mtu throughput example. it is working fine upto 50 bytes packet size but when i try...
so, after getting it to compile, now i can no longer write to flash memory and i don't knwo why i am getting this error now. now sure if it is a result of nrf_dfu_flash and...
hi.....
i am interested in Mesh ,actually i want to understand the flow of mesh program (eg light switch example )how does it work,how it transferring from client to server...
Hi all,
In order to lower the power consumption of my device I have been experimenting with WFE. When using WFE I see that the interrupt latency is increased from ~4µs to...
Onl
I have 40 kb of data i need to send, and what i thought was using notification by creating a timer, which will be started as soon as device gets connected, in...
I am trying to interface with a I²C OLED display using Zephyr’s SSD1306 driver. The driver uses i2c_burst_write, which itself requires that i2c_transfer support gather writes;...
This is on SDK 15 : Not all services are reported when doing service discovery on more than one connection at a time.
Basically, ' ble_db_discovery .c' uses ' m_pending_usr_evt_index...
Hello, I am using the nRF51422 Development kit with SDK11. I am using the proximity application for the battery level service. I would like to strictly advertise to a single...
Hi,
I have an application where I have for example 5 BLE transmitting devices . Each device has one push button and each device is assigned to a number 1-5. I also have...
Dear nordic,
I am new in this open thread i tested your examples its working fine. i also tested CLI example i think its working but i didn't see a response in terminal...
I have a few Bluetooth transmitters based on nRF52832. My receiver devices are mainly iOS and Android mobile devices. I'm considering of replacing them with nRF52840 for Bluetooth...
