I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Example Project: UART/Serial Port Emulation over BLE
My Environment: Segger Embedded Studio v3.52, Nordic SDK 15.2, Soft Device s132, nRF52 DK, nRF Toolkit for iOS
It...
Hello,
I have several questions regarding BLE beaconing and scanning that I feel are pretty basic but I can't seem to find the answer. I have a nRF52840 Dongle that uses...
Hello,
Thank you for considering my inquiry! I am looking for an example project with the firmware to run a gateway through the PC, nRFconnect software, and a nRF52840...
Hi,
I'm developing an application with the following hardware and software design components:
- nrf52840 DK with attached sensor
- nrf52840 USB dongle attached to debian...
Hi, I have some issues with my eclipse setup, I have installed all packages and followed the tutorial ( https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/development...
Hello,
I am working on bootloader on nRF24LE1, for which a protected region should be configured. Therefore, I need to change NUPP in infoPage.
So my question is, is there...
Hi.
I watched the examples and docs with the on-off model. I tried to run these examples and configure. I don't understand when I need to use a server model when client...
I am seeing some behavior in BLE advertisement mode , that I would like to get feedback from expert in this forum. I am using modified Keyboard HID example, using nrf51 BLE...
Hi,
I'm using nrf52DK and 12.3V SDK .
in keil i can able to go to the debug session but when i press run button it is not working.
what could be issue ???
I have enabled RX address 0 only, (value of RXADDRESSES field is 0x01)
But still I got a received package interupt where RXMATCH has a value of 0x07, indicating that I...
Tx Radiated spurious emissions (1-18GHz): should be able to force the radio into a continuous transmit mode on a specific channel. The device should be transmitting with as...
Hello,
the BT specification states the following:
Is this particular requirement to be taken care by Nordic's customer using the BTIC? i.e. LE PHY qualification test...
Hi,
I want to use bsp_event_handler in SDK v11.0.0 . But the code is not getting compiled.
On building, it throws an error "error:#20: identifier "BSP_BUTTON_ACTION_RELEASE...
Hi,
I'm using NRF_LOG to print information via RTT backend (RTT viewer v6.20) and it has been working so far. After adding a single call to a function that reads 128 bytes...
