Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi,
I am using app_timer and SoftDevice in NRF52810.
I am storing app_timer_cnt_get() value after releasing button and after completing BLE Advertisment.
as I am starting...
Hey all,
I have started working with this board around a month ago, and start to understand it little by little. I have a program that communicates with a display over UART...
Attempting to program an nRF52840 dongle with sniffer_nrf52840dongle_nrf52840_7cc811f.hex, using nRF Connect Programmer v1.4.8, on Windows 7
Upon clicking "Write", the red...
HI,
I am trying to use STTS751-1DP3F temp. sensor with nr52832. The drivers for sensors are given on:
https://github.com/STMicroelectronics/STMems_Standard_C_drivers/tree...
I have some old production code that uses s110 v 5/6 and SDK 8.0.0 (perhaps - no one seems to know). The production device has never been able to do a bonded reconnect correctly...
Hi,
Your online power estimator only concerns nRF52840/832/810.
How to get a value when using nRF5233 with CTE activated for AoA ?
In other words, what is the additional...
I'm trying to create application for working with nRF52 device. I have completed provisioning mesh success, and receive notification message about success operation (work...
I know that SoftDevice 110 is old but I am stuck with it as it is on a production device with nRF51822. For some reason when I call sd_ble_gap_adv_data_set() with a non NULL...
I am developing software with the following features.
Communicates between two boards with nRF52840, nRF5 SDK 15.3.0, and its S140
Activate both extended advertising...
When I use this setup, when the specified duration expires, should I get a BLE_ADV_EVT_IDLE event? I don't seem to get one, even though I'm testing for it. SDK 17.0.2 / S...
Hi,
I have 4 sensors on my custom board and I'm planning to use BLE. I want to read data from all 4 sensors every 200ms. I'm planning to use app_timer for that and read...
Hi
Using demo usbd_cdc_acm and found a very strange bug!
Even I disabled the flow control of uart , the 52840 device still need to control the DTR signal to ensure UART...
Hi Nordic Team,
I am developing a CoAP client on the nRF9160 DK, and am having trouble with longer proxy-uri's; short URIs ( 268 characters and below ) work fine and the...
