Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
In the Mesh SDK the scanner.c file has a power set to 0dBm:
void scanner_init(bearer_event_flag_callback_t packet_process_cb) { memset(&m_scanner, 0, sizeof(m_scanner));...
Hello,
I have nRF52832 and a smart phone with android 7.0.
I want to make a direct BLE connection between nRF and the smart phone, where nRF is a Central device (initiating...
I try to print with serial. How can I print something without a format. I want to print it directly. If yes, which function should I call?
For example, What I am looking...
I have included the reference design for the nRF52840 in my project. Unfortunately, the VIAs in Pads have a hole diameter of 0.15mm and a diameter of 0.35mm and are also still...
Hi,
I checkout v1.0.0 and try to build the at_client-sample but it fails. I cannot see anything I did wrong. I'm attaching the exact steps to reproduce the behaviour.
...
Hi nordic community
I am trying to send stop command to my device(which is connected to my NRF 52840) from my ble module(NRF 52480) after my android disconnected from the...
Hi Nordic engineer:
When I used examples\multi protocol\ble thread\ble_thread_dyn_mtd_coap_cli, I found that the device could not automatically assign LEADER, Router, and...
Hello and Thank you In Advance for Your Assistance. I have been working several days just to get a UART running for interface to a peripheral.
I am trying to connect a UART...
Hi,
As per the document(nrf91_at_commands_v0.9.1) for GPS SNR testing command "AT%XRFTEST=2,1,0" output is single integer as below .
but i am getting output like below...
We are using nRF52832 in our design. We want to collect sensor information along with time stamp. So I took nRF calendar application and tested the same. It was working fine...
I have developed an application that reads data from an analog sensor and transmits data with UART. This app is based off the SDK v14.x uart example, and SAADC example. While...
Hi.
I am developing zigbee product with security function (using install codes).
1. function cmd_zb_install_code in zigbee_cli_cmd_bdb.c, there is a comment as bellows...
Hi, I'm using proxy_client and proxy_server from light_switch examples of mesh sdkv2.1.1. The provision process gets successful with android mobile using nRF Mesh App but...
