I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi, are my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS or AIN_2_3_PS will not...
Hello,
I'm currently seeking for parameters that could improve our ANT communication stability. I read, that there are possibly override parameters in the FIRC that have...
Hi all,
I try to reduce the power consumption of my GZLL host (RFDduino/nRF51822).
I use the Arduino IDE to program my RFDuino.
My Idea was to synchronize the host and...
Trying to flash a program with Keil. Worked fine with SDK 5.2, now with SDK 6.0 get the error: Insufficient RAM for Flash Algorithms.
My options for RAM:
Start: 0x20002000...
Hi, Nordic
I added "//" to the srccode of main.c in project ble_app_hrs just like below
bond_manager_init();
// ble_stack_init();
ble_error_log_init();
timers_init...
L.S.
Suppose I want to customize the transmit power at installation time, not at build time or production time, how would I go about it?
I have adapted the proximity...
Hello,
I want to use DFU with single mode mode.
I included in build dfu_single_bank.c instead of dfu_dual_bank.c.
But after that DFU device begin to work with errors...
hello,
I am working with S130 demo app. But I could not find any registering of event handler being done usind softdevice_ble_evt_handler_set(). In both S110 and S120 demo...
With the maximum SPI speed of 8 Mbps, I was expecting to be able to send 2 bytes in just a little over 2 us, but it takes a lot longer. It appears that the mandatory event...
Hi all,
I'm trying to follow this Nordic blog post in order to use Luna Eclipse, GDB and J-link for debugging of ble_app_hrs from Nordic SDK 6.1 on a PCA10001
It is...
Hi everyone,
I dont know if I encounter these issues because of iOS 8.0 but I'm not able to receive data from the console, send via PCA100001, on my iPhone. Though, what...
I have managed to successfully integrate BLE DFU service in my app, but updating firmware via MCP is a bit confusing.
I connect MCP to my device -> discover services -...
Hi,
I plan to have my device without any forms of external user input, like buttons serial ports, and similar.
You can only replace the battery, that's it.
I'd also...
Hi,
I tried to migrate S110 example code with uart_ble service , which is working fine on S110, to S120 v2 soft device. Fix some minor missmatch with configuration structures...