Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
When debugging the exercise 1 application from `Lesson 2 – Reading buttons and controlling LEDs` of `nRF Connect SDK Fundamentals`, I cannot set a breakpoint wherever I want...
Working in a Windows 64 environment with nRF Connect SDK v1.5.0. Target is a custom nRF5340 board connected through a nRF5340-PDK as a debugger, via USB.
I can no longer...
Hello
nPM Power UP v 2.24 detects nPM2100 EK, but does not detect the CR2032 battery. The active battery model selected is CR2032 and the fuel gauge is enabled.
I placed...
Hello,
We currently use an nRF51822 device in our product with the top marking QFABC0 .
We understand that NRF51822-QFAB is the ordering part number, and that QFABC0 is...
I'm working on a project for the nRF54L15. Until now I have not been using mcuboot, but since I added SB_CONFIG_BOOTLOADER_MCUBOOT=y to my sysbuild.conf, I get an error when...
in the datasheet table 80 "GPIO port mapping" the function "CAN-RX" is only listed on P9.4 and P2.8 are these the only two pins it can be assigned to ?
I am struggling to...
Hi Dev,
Development platform: NRF54L15 + NCS 3.0.2. We use k_uptime_get() to obtain the system uptime and perform task scheduling. Everything runs normally when the device...
I need to create a firmware to the nRF9151 SMA DK that can send a message to me (it can be via MQTT, but I prefer the nRF Cloud) containing info about the location of the...
Hi,
I'm trying to debug a Zigbee issue and for that I want to try some Zigbee samples on the nRF52840DK. But all links for Zigbee in docs.nordicsemi seem to be broken. All...
I'm running into a bit of an annoying situation every time i run ' west flash --build-dir ./build' in the command line. It rebuilds always after a successful build i set when...
To anyone trying to create the reflector for this combination there is an important conf file to add to the project. You should add android_ranging.conf to your build that...
In NCS v3.3.0 the signing of binaries fails when building the Non-Secure application (build with TF-M) in combination with XIP, split images and disabled partition manager...
in Memfault I see the device ID number for each device such as 41EF6BB8FB6C9AF9. Is the distribution for the first 3 bytes the same as the distribution for the last 3 bytes...
Hello! I'm using Zepyhr OS with nrf connect SDK v3.2.3 and the NRF54L15 hardware.
I am using UARTE with the async driver (direct memory access). This is my uart configuration...
